HP XP P9500 Storage - Manual (Page 306)

# cfgadm -al
Ap_Id Type Receptacle
Occupant Cond
system:slot0 cpu/mem connected
configured ok
system:slot1 sbus-upa connected
configured ok
2
.
Check the newly recognized path in the syslog.
The following is an example of the command. Specify the number of lines
to display taking into consideration that three to four lines for each
recognized path are output to the log.
# tail -10 /var/adm/messages
Apr 2 16:02:57 shiga genunix: [ID 408114 kern.info] /pseudo/
dlmndrv@2/dlmfdrv@w50060e8010027a80,5 (dlmfdrv54) online
Apr 2 16:02:57 shiga devfsadmd[89]: [ID 937045 daemon.error]
failed to lookup dev name for /pseudo/dlmndrv@2/
dlmfdrv@w50060e8010027a80,5
Apr 2 16:03:31 shiga scsi: [ID 583861 kern.info] ssd4126 at
fp2: unit-address w50060e8010027a84,5: 642400
Apr 2 16:03:31 shiga genunix: [ID 936769 kern.info] ssd4126 is /
pci@400/pci@2/pci@0/pci@8/SUNW,qlc@0/fp@0,0/
ssd@w50060e8010027a84,5
Apr 2 16:03:31 shiga genunix: [ID 408114 kern.info] /pci@400/
pci@2/pci@0/pci@8/SUNW,qlc@0/fp@0,0/ssd@w50060e8010027a84,5
(ssd4126) online
Apr 2 16:03:31 shiga devfsadmd[89]: [ID 937045 daemon.error]
failed to lookup dev name for /pci@400/pci@2/pci@0/pci@8/
SUNW,qlc@0/fp@0,0/ssd@w50060e8010027a84,5
Apr 2 16:03:36 shiga scsi: [ID 583861 kern.info] ssd4127 at
fp3: unit-address w50060e8010027a84,5: 642400
Apr 2 16:03:36 shiga genunix: [ID 936769 kern.info] ssd4127 is /
pci@400/pci@2/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0/
ssd@w50060e8010027a84,5
Apr 2 16:03:36 shiga genunix: [ID 408114 kern.info] /pci@400/
pci@2/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0/ssd@w50060e8010027a84,5
(ssd4127) online
Apr 2 16:03:36 shiga devfsadmd[89]: [ID 937045 daemon.error]
failed to lookup dev name for /pci@400/pci@2/pci@0/pci@8/
SUNW,qlc@0,1/fp@0,0/ssd@w50060e8010027a84,5
#
In the above example, underlines indicate the log entries of the newly
recognized path.
3
.
Use the dlmsetconf utility shown below to update the HDLM driver
configuration definition file (/ kernel/drv/dlmfdrv.conf).
# /opt/DynamicLinkManager/bin/dlmsetconf
For details about the dlmsetconf utility, see The dlmsetconf Utility for
Creating the HDLM Driver Configuration Definition File on page 7-23 .
4
.
Execute the dlmcfgmgr utility so that the HDLM driver can recognize the
newly added path.
The following is an example of the command:
4-44
HDLM Operation
Hitachi Dynamic Link Manager User Guide for Solaris ®