NORD Drivesystems BU0180 User Manual
Page 96
SK 180E Manual for frequency inverters
96
Pre-series version
BU 0180 GB-0914
Parameter
{Factory setting}
Setting value / Description / Note
Device
Supervisor
Parameter
set
P402
[-01]
...
[-06]
Adjustment: 0%
(Analog input adjustment: 0%)
S
-50.00 ... 50.00 V
{ all 0.00 }
[-01] = Analog input 1, Function of analog input 1 integrated into the FI
[-02] = Analog input 2, Function of analog input 2 integrated into the FI
[-03] = Ext. Analog input 1,
AIN1 of the first I/O extension (SK xU4-IOE)
[-04] = Ext. Analog input 2,
AIN2 of the first I/O extension (SK xU4-IOE)
[-05] = Ext.
A.in
1 2nd IOE,
AIN1 of the second I/O extension (SK xU4-IOE)
[-06] = Ext.
A.in
2 2nd IOE,
AIN2 of the second I/O extension (SK xU4-IOE)
This parameter sets the voltage which should correspond with the minimum value of the selected
function for the analog input 1 or 2. In the factory setting (setpoint) this value is equivalent to the
setpoint set via P104 >Minimum frequency<.
Note
SK 1x0E
For the adjustment of the integrated analog inputs of the SK1x0E to the type of analog signals, the
following values must be set:
0
– 10 V
→ 0.00 V
2
– 10 V
→ 2.00 V
0
– 20 mA → 0.00 V (switch in internal resistance via DIP switch S1 (Section.: 5.2.2.2)
4
– 20 mA → 1.00 V (switch in internal resistance via DIP switch S1 (Section.: 5.2.2.2)
SK xU4-IOE
Standardisation to typical signals, such as 0(2)-10V or 0(4)-20mA is carried out via the DIP switch
on the I/O-extension module. In this case, additional adjustment of parameters (P402) and (P403)
must not be carried out.
P403
[- 01]
...
[- 06]
Adjustment: 100%
(Analog input adjustment: 100%)
S
-50.00 ... 50.00 V
{ all 0.00 }
[-01] = Analog input 1, Function of analog input 1 integrated into the FI
[-02] = Analog input 2, Function of analog input 2 integrated into the FI
[-03] = Ext. Analog input 1,
AIN1 of the first I/O extension (SK xU4-IOE)
[-04] = Ext. Analog input 2,
AIN2 of the first I/O extension (SK xU4-IOE)
[-05] = Ext.
A.in
1 2nd IOE,
AIN1 of the second I/O extension (SK xU4-IOE)
[-06] = Ext.
A.in
2 2nd IOE,
AIN2 of the second I/O extension (SK xU4-IOE)
This parameter sets the voltage which should correspond with the maximum value of the selected
function for the analog input 1 or 2. In the factory setting (setpoint) this value is corresponds with
the setpoint set via P105 >Maximum frequency<.
Note
SK 1x0E
For the adjustment of the integrated analog inputs of the SK1x0E to the type of analog signals, the
following values must be set:
0
– 10 V
→ 10.00 V
2
– 10 V
→ 10.00 V
0
– 20 mA → 5.00 V (switch in internal resistance via DIP switch S1 (Section.: 5.2.2.2)
4
– 20 mA → 5.00 V (switch in internal resistance via DIP switch S1 (Section.: 5.2.2.2)
SK xU4-IOE
Standardisation to typical signals, such as 0(2)-10V or 0(4)-20mA is carried out via the DIP switch
on the I/O-extension module. In this case, additional adjustment of parameters (P402) and (P403)
must not be carried out.