Watlow EZ-ZONE PM Integrated Controller - Manual (Page 70)

Watlow EZ-ZONE ® PM Integrated Controller • 67 • Chapter 6 Setup Page
6
Chapter 6: Setup Page
Navigating the Setup Page
[``Ai]
[`Set]
Analog Input Menu
[```1]
[``Ai]
Analog Input (1 to 2)
[`SEn] Sensor Type
[`Lin] TC Linearization
[`rt;L] RTD Leads
[Unit] Units
[`S;Lo] Scale Low
[`S;hi] Scale High
[`r;Lo] Range Low
[`r;hi] Range High
[`P;EE] Process Error Enable
[`P;EL] Process Error Low Value
[``t;C] Thermistor Curve
[``r;r] Resistance Range
[`FiL] Filter
[`i;er] Input Error Latching
[`dEC] Display Precision
[`s;ba] Sensor Backup
[`i;Ca] Calibration Offset **
[`Ain] Analog Input Value **
[`i;Er] Input Error Status **
[`Lnr]
[`Set]
Linearization Menu
[```1]
[`Lnr]
Linearization (1 to 2)
[``Fn] Function
[Unit] Units
[`ip;1] Input Point 1
[`op;1] Output Point 1
[`ip;2] Input Point 2
[`op;2] Output Point 2
[`ip;3] Input Point 3
[`op;3] Output Point 3
[`ip;4] Input Point 4
[`op;4] Output Point 4
[`ip;5] Input Point 5
[`op;5] Output Point 5
[`ip;6] Input Point 6
[`op;6] Output Point 6
[`ip;7] Input Point 7
[`op;7] Output Point 7
[`ip;8] Input Point 8
[`op;8] Output Point 8
[`ip;9] Input Point 9
[`op;9] Output Point 9
[ip;10] Input Point 10
[op;10] Output Point 10
[``Pu]
[`Set]
Process Value Menu
[```1]
[``Pu]
Process Value (1 to 2)
[``Fn] Function
[P;unt] Pressure Units
[A;unt]
Altitude Units
[`b;pr] Barometric Pressure
[`FiL]
Filter
[`dio]
[`Set]
Digital Input/Output Menu
[```5]
[`dio]
Digital I/O (5 to 12)
[`dir] Direction
[``Fn] Output Function
[``Fi] Output Function Instance
[`o;Ct] Output Control
[`o;tb] Output Time Base
[`o;Lo] Output Low Power Scale
[`o;hi] Output High Power Scale
[`leu] Active Level
[``Fn] Action Function
[``Fi] Function Instance
To navigate to the Setup Page, follow the steps below:
1. From the Home Page, press both the Up ¿ and Down ¯ keys for six seconds. [``Ai] will appear in the upper
display and [`Set] will appear in the lower display.
2. Press the Up ¿ or Down ¯ key to view available menus.
3. Press the Advance Key
‰ to enter the menu of choice.
4. If a submenu exists (more than one instance), press the Up ¿ or Down ¯ key to select and then press the Ad-
vance Key ‰ to enter.
5. Press the Up ¿ or Down ¯ key to move through available menu prompts.
6. Press the Infinity Key ˆ to move backwards through the levels: parameter to submenu; submenu to menu;
menu to Home Page.
7. Press and hold the Infinity Key ˆ for two seconds to return to the Home Page.
On the following pages, top level menus are identified with a yellow background color.
Note:
Keys must be held continuously until [`SEt] is displayed in green. If keys are released when 'OPEr' is dis-
played, press the infinity key or reset key to exit and repeat until [`SEt] is displayed.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no sub-
menus will appear.
Note:
Some of the listed parameters may not be visible. Parameter visibility is dependent upon controller part
number.
** These parameters/prompts are available with firmware revisions 11.0 and above.