Siemens Brodersen MC55 AT User Manual

At command manual

AT Command Manual

for

Brodersen Products with Siemens MC55

Modem Engine

V. 04.00 / April 2006 / Doc 40232

Brodersen Controls A/S ● Industrivej 3 ● DK-4000 Roskilde ● Tel: +45 46 74 00 00 ● Fax: +45 46 75 73 36

E-mail: [email protected] ● Internet: www.brodersencontrols.com

Table of contents

Document Outline

Contents
List of Tables
List of Figures
1. Introduction
- 1.1 Scope of the document
- 1.2 Related documents
- 1.3 Document conventions
  - 1.3.1 Quick reference table
  - 1.3.2 Superscript notation for parameters and values
- 1.4 AT Command Syntax
  - 1.4.1 Using Parameters
  - 1.4.2 Combining AT commands on the same command line
- 1.5 Supported character sets
  - 1.5.1 GSM alphabet tables and UCS2 character values
  - 1.5.2 UCS2 and GSM data coding and conversion for SMS text mode
    - 1.5.2.1 Implementing output of SIM data to Terminal (direction TA to TE)
    - 1.5.2.2 Implementing input of Terminal data to SIM (direction TE to TA)
- 1.6 Serial Interface Flow Control
  - 1.6.1 Software Flow Control (XON/OFF Handshake)
  - 1.6.2 Hardware Flow Control (RTS/CTS Handshake)
- 1.7 Unsolicited Result Code Presentation
  - 1.7.1 Communication between Customer Application and MC55
- 1.8 Common PCN Handset Specification (CPHS)
- 1.9 Errors and Messages
2. Configuration Commands
- 2.1 AT&F Set all current parameters to manufacturer defaults
- 2.2 AT&V Display current configuration
  - 2.2.1 AT&V responses
- 2.3 AT&W Stores current configuration to user defined profile
- 2.4 ATQ Set result code presentation mode
- 2.5 ATV Set result code format mode
  - 2.5.1 Verbose and numeric result codes
- 2.6 ATX Set CONNECT result code format and call monitoring
- 2.7 ATZ Set all current parameters to user defined profile
- 2.8 AT+CFUN Set phone functionality
  - 2.8.1 Wake up the ME from SLEEP mode
- 2.9 AT^SMSO Switch off mobile station
- 2.10 AT+GCAP Request complete TA capabilities list
- 2.11 AT+CMEE Mobile Equipment Error Message Format
  - 2.11.1 CME/CMS Error Code Overview
- 2.12 AT+CSCS Select TE character set
- 2.13 AT^SCFG Extended Configuration Settings
- 2.14 AT^SM20 Set M20 compatibility mode
3. Status Control Commands
- 3.1 AT+CMER Mobile Equipment Event Reporting
- 3.2 AT+CIND Indicator control
- 3.3 AT^SIND Extended Indicator Control
- 3.4 AT+CEER Extended Error Report
- 3.5 ATS18 Extended call release report
- 3.6 AT+CPAS Mobile equipment activity status
- 3.7 AT+WS46 Select wireless network
4. Serial Interface Control Commands
- 4.1 AT\Q Flow control
- 4.2 AT&C Set Data Carrier Detect (DCD) Line mode
- 4.3 AT&D Set circuit Data Terminal Ready (DTR) function mode
- 4.4 AT&S Set circuit Data Set Ready (DSR) function mode
- 4.5 ATE Enable command echo
- 4.6 AT+ILRR Set TE-TA local rate reporting
- 4.7 AT+IPR Set fixed local rate
  - 4.7.1 Autobauding
- 4.8 AT+CMUX Enter multiplex mode
  - 4.8.1 Restrictions on Multiplex mode
  - 4.8.2 Second serial interface ASC1
5. Security Commands
- 5.1 AT+CPIN PIN Authentication
  - 5.1.1 What to do if PIN or password authentication fails?
- 5.2 AT+CPIN2 PIN2 Authentication
- 5.3 AT^SPIC Display PIN counter
- 5.4 AT+CLCK Facility lock
- 5.5 AT^SLCK Facility lock
- 5.6 AT+CPWD Change Password
- 5.7 AT^SPWD Change Password
6. Identification Commands
- 6.1 ATI Display product identification information
- 6.2 AT+CGMI Request manufacturer identification
- 6.3 AT+GMI Request manufacturer identification
- 6.4 AT+CGMM Request model identification
- 6.5 AT+GMM Request model identification
- 6.6 AT+CGMR Request revision identification of software status
- 6.7 AT+GMR Request revision identification of software status
- 6.8 AT+CGSN Request International Mobile Equipment Identity (IMEI)
- 6.9 AT+GSN Request International Mobile Equipment Identity (IMEI)
- 6.10 AT+CIMI Request International Mobile Subscriber Identity (IMSI)
7. Call related Commands
- 7.1 Call Status Information
- 7.2 ATA Answer a call
- 7.3 ATD Mobile originated call to specified number
- 7.4 ATD> Mobile originated call using specific memory and index number
- 7.5 ATD> Mobile originated call from active memory using index number
- 7.6 ATD> Mobile originated call from active memory using corresponding field
- 7.7 ATDI Mobile originated call to ISDN number
- 7.8 ATDL Redial last number used
- 7.9 ATH Disconnect existing connection
- 7.10 AT+CHUP Hang up call
- 7.11 ATS0 Set number of rings before automatically answering a call
- 7.12 ATS6 Set pause before blind dialing
- 7.13 ATS7 Set number of seconds to wait for connection completion
- 7.14 ATS8 Set number of seconds to wait for comma dialing modifier
- 7.15 ATS10 Set disconnect delay after indicating the absence of data carrier
- 7.16 ATO Switch from command mode to data mode / PPP online mode
- 7.17 +++ Switch from data mode to command mode
- 7.18 AT+CBST Select bearer service type
- 7.19 AT+CRLP Select radio link protocol parameters for originated non-transparent data calls
- 7.20 AT+CLCC List current calls of ME
- 7.21 AT^SLCC Siemens defined command to list current calls of ME
- 7.22 AT+CR Service reporting control
- 7.23 AT+CRC Set Cellular Result Codes for incoming call indication
- 7.24 AT+CSNS Single Numbering Scheme
- 7.25 AT^SCNI List Call Number Information
- 7.26 AT^SLCD Display Last Call Duration
- 7.27 AT^STCD Display Total Call Duration
- 7.28 ATP Select pulse dialing
- 7.29 ATT Select tone dialing
8. Network Service Commands
- 8.1 AT+COPN Read operator names
- 8.2 AT+COPS Operator Selection
- 8.3 AT^SOPS Extended Operator Selection
- 8.4 AT+CREG Network registration
- 8.5 AT+CSQ Signal quality
- 8.6 AT^SMONC Cell Monitoring
- 8.7 AT^SMOND Cell Monitoring
- 8.8 AT^MONI Monitor idle mode and dedicated mode
  - 8.8.1 AT^MONI responses
  - 8.8.2 Service states
- 8.9 AT^MONP Monitor neighbour cells
  - 8.9.1 AT^MONP responses
- 8.10 AT^SMONG GPRS Monitor
  - 8.10.1 AT^SMONG Cell Info Table
- 8.11 AT^SALS Alternate Line Service
- 8.12 AT^SHOM Display Homezone
- 8.13 AT^SPLM Read the PLMN list
- 8.14 AT+CPOL Preferred Operator List
- 8.15 AT^SPLR Read entry from the preferred operators list
- 8.16 AT^SPLW Write an entry to the preferred operators list
9. Supplementary Service Commands
- 9.1 AT+CACM Accumulated call meter (ACM) reset or query
- 9.2 AT^SACM Advice of charge and query of ACM and ACMmax
- 9.3 AT+CAMM Accumulated call meter maximum (ACMmax) set or query
- 9.4 AT+CAOC Advice of Charge information
- 9.5 AT+CCUG Closed User Group
- 9.6 AT+CCFC Call forwarding number and conditions control
- 9.7 AT+CCWA Call Waiting
- 9.8 AT+CHLD Call Hold and Multiparty
- 9.9 AT+CLIP Calling Line Identification Presentation
- 9.10 AT+CLIR Calling line identification restriction
- 9.11 AT+COLP Connected Line Identification Presentation
- 9.12 AT+CPUC Price per unit and currency table
- 9.13 AT+CSSN Supplementary service notifications
- 9.14 AT+CUSD Supplementary service notifications
10. Internet Service Commands
- 10.1 AT^SICS Internet Connection Setup Profile
  - 10.1.1 Example: Default values of a CSD connection profile
  - 10.1.2 Example: GPRS connection profile
- 10.2 AT^SICI Internet Connection Information
  - 10.2.1 Checking Connection Profile Status
- 10.3 AT^SISS Internet Service Setup Profile
- 10.4 AT^SISI Internet Service Information
- 10.5 AT^SISO Internet Service Open
  - 10.5.1 Example: Accepting / Rejecting Socket Connection Request from Remote Client
- 10.6 AT^SISC Internet Service Close
- 10.7 AT^SISR Internet Service Read Data
  - 10.7.1 Example: Socket Host Reads Small Amounts of UDP Data Packets (URC Mode)
- 10.8 AT^SISW Internet Service Write Data
  - 10.8.1 Usage of parameter
- 10.9 AT^SISE Internet Service Error Report
- 10.10 Internet Service URC "^SIS"
- 10.11 Examples of how to Configure and Use Internet Service Profiles
11. GPRS Commands
- 11.1 AT+CGACT PDP context activate or deactivate
- 11.2 AT+CGANS Manual response to a network request for PDP context activation
- 11.3 AT+CGATT GPRS attach or detach
- 11.4 AT+CGAUTO Automatic response to a network request for PDP context activation
- 11.5 AT+CGEREP GPRS event reporting
- 11.6 AT+CGDATA Enter data state
  - 11.6.1 Automatic deactivation of PDP context during dial-up PPP
- 11.7 AT+CGDCONT Define PDP Context
- 11.8 AT+CGPADDR Show PDP address
- 11.9 AT+CGQMIN Quality of Service Profile (Minimum acceptable)
- 11.10 AT+CGQREQ Quality of Service Profile (Requested)
- 11.11 AT+CGREG GPRS Network Registration Status
- 11.12 AT+CGSMS Select service for MO SMS messages
- 11.13 AT^SGAUTH Set type of authentication for PPP connection
- 11.14 AT^SGCONF Configuration of GPRS related Parameters
- 11.15 ATA Manual response to a network request for PDP context activation
- 11.16 ATD*99# Request GPRS service
- 11.17 ATD*98# Request GPRS IP service
- 11.18 ATH Manual rejection of a network request for PDP context activation
- 11.19 ATS0 Automatic response to a network request for PDP context activation
- 11.20 Using GPRS AT commands (Examples)
- 11.21 Using the GPRS dial command ATD
12. FAX Commands
- 12.1 FAX parameters
  - 12.1.1 Summary of Fax Class 2 URCs defined by EIA PN-2388
- 12.2 AT+FBADLIN Bad Line Threshold
- 12.3 AT+FBADMUL Error Threshold Multiplier
- 12.4 AT+FBOR Query data Bit Order
- 12.5 AT+FCIG Query or set the Local Polling ID
- 12.6 AT+FCLASS Fax: Select, read or test service class
- 12.7 AT+FCQ Copy Quality Checking
- 12.8 AT+FCR Capability to Receive
- 12.9 AT+FDCC Query or set capabilities
- 12.10 AT+FDFFC Data Compression Format Conversion
- 12.11 AT+FDIS Query or set session parameters
- 12.12 AT+FDR Begin or continue phase C Data Reception
- 12.13 AT+FDT Data Transmission
- 12.14 AT+FET End a page or document
- 12.15 AT+FK Kill operation, orderly FAX abort
- 12.16 AT+FLID Query or set the Local Id setting capabilities
- 12.17 AT+FMDL Identify Product Model
- 12.18 AT+FMFR Request Manufacturer Identification
- 12.19 AT+FOPT Set bit Order independently
- 12.20 AT+FPHCTO DTE Phase C Response Timeout
- 12.21 AT+FREV Identify Product Revision
- 12.22 AT+FRH Receive Data Using HDLC Framing
- 12.23 AT+FRM Receive Data
- 12.24 AT+FRS Receive Silence
- 12.25 AT+FTH Transmit Data Using HDLC Framing
- 12.26 AT+FTM Transmit Data
- 12.27 AT+FTS Stop Transmission and Wait
- 12.28 AT+FVRFC Vertical Resolution Format Conversion
13. Short Message Service (SMS) Commands
- 13.1 SMS parameters
- 13.2 AT+CMGC Send an SMS command
- 13.3 AT+CMGD Delete short message
- 13.4 AT+CMGF Select SMS message format
- 13.5 AT+CMGL List SMS messages from preferred store
- 13.6 AT+CMGR Read SMS messages
- 13.7 AT+CMGS Send Short Message
- 13.8 AT+CMGW Write Short Messages to Memory
- 13.9 AT+CMSS Send short messages from storage
- 13.10 AT+CNMA New Message Acknowledgement to ME/TE, only phase 2+
- 13.11 AT+CNMI New short Message Indication
- 13.12 AT+CPMS Preferred SMS message storage
- 13.13 AT+CSCA SMS Service Center Address
- 13.14 AT+CSCB Select Cell Broadcast Message Indication
- 13.15 AT+CSDH Show SMS text mode parameters
- 13.16 AT+CSMP Set SMS text Mode Parameters
- 13.17 AT+CSMS Select Message Service
- 13.18 AT^SLMS List SMS Memory Storage
- 13.19 AT^SMGL List Short Messages from preferred store without setting status to REC READ
- 13.20 AT^SMGO Set or query SMS overflow presentation mode or query SMS overflow
- 13.21 AT^SMGR Read short message without setting status to REC READ
- 13.22 AT^SSCONF SMS Command Configuration
- 13.23 AT^SSDA Set SMS Display Availability
- 13.24 AT^SSMSS Set Short Message Storage Sequence
14. SIM related Commands
- 14.1 AT+CRSM Restricted SIM Access
- 14.2 AT^SXSM Extended SIM Access
- 14.3 AT^SCKS Query SIM and Chip Card Holder Status
- 14.4 AT^SCID Display SIM card identification number
- 14.5 AT+CXXCID Display card ID
15. SIM Application Toolkit (SAT) Commands
- 15.1 AT^SSTA SAT Interface Activation
- 15.2 ^SSTN SAT Notification
- 15.3 AT^SSTGI SAT Get Information
- 15.4 AT^SSTR SAT Response
16. Phonebook Commands
- 16.1 Sort Order for Phonebooks
- 16.2 AT+CPBR Read from Phonebook
- 16.3 AT+CPBS Select phonebook memory storage
- 16.4 AT+CPBW Write into Phonebook
- 16.5 AT^SPBC Find first matching entry in sorted phonebook
- 16.6 AT^SPBD Purge phonebook memory storage
- 16.7 AT^SPBG Display phonebook entries in alphabetical order
- 16.8 AT^SPBS Step through the selected phonebook alphabetically
- 16.9 AT+CNUM Read own numbers
- 16.10 AT^SDLD Delete the 'last number redial' memory
17. Audio Commands
- 17.1 Audio programming model
- 17.2 ATL Set monitor speaker loudness
- 17.3 ATM Set monitor speaker mode
- 17.4 AT+CLVL Loudspeaker volume level
- 17.5 AT+CMUT Mute control
- 17.6 AT+VTD Tone duration
- 17.7 AT+VTS DTMF and tone generation
- 17.8 AT^SAIC Audio Interface Configuration
- 17.9 AT^SNFA Set or query of microphone attenuation
- 17.10 AT^SNFD Set audio parameters to manufacturer default values
- 17.11 AT^SNFI Set microphone path parameters
- 17.12 AT^SNFM Set microphone audio path and power supply
- 17.13 AT^SNFO Set audio output (= loudspeaker path) parameter
- 17.14 AT^SNFPT Set progress tones
- 17.15 AT^SNFS Select audio hardware set
- 17.16 AT^SNFTTY Signal TTY/CTM audio mode capability
- 17.17 AT^SNFV Set loudspeaker volume
- 17.18 AT^SNFW Write audio setting in non-volatile store
- 17.19 AT^SRTC Ring tone configuration
18. Hardware related Commands
- 18.1 AT+CCLK Real Time Clock
- 18.2 AT+CALA Set alarm time
- 18.3 AT^SBC Battery Charge Control
  - 18.3.1 Responses returned by read command
- 18.4 AT^SBV Battery/Supply Voltage
- 18.5 AT^SCTM Set critical operating temperature presentation mode or query temperature
- 18.6 AT^SSYNC Configure SYNC Pin
  - 18.6.1 ME status indicated by status LED patterns
19. Miscellaneous Commands
- 19.1 A/ Repeat previous command line
- 19.2 ATS3 Set command line termination character
- 19.3 ATS4 Set response formatting character
- 19.4 ATS5 Write command line editing character
20. Appendix
- 20.1 Restricted access to SIM data after SIM PIN authentication
- 20.2 Star-Hash (*#) Network Commands
- 20.3 Available AT Commands and Dependency on SIM PIN
- 20.4 Availability of AT Commands Depending on Operating Mode of ME
- 20.5 AT Command Settings storable with AT&W
- 20.6 Factory Default Settings Restorable with AT&F
- 20.7 Summary of Unsolicited Result Codes (URC)
- 20.8 Alphabetical List of AT Commands