TA Triumph-Adler DC 2020 - Manual (Page 170)

U03300
U03500
U03600
U03700
U04000
U04100
U04200
U04300
U04400
Section 8 Reference Information
8-10
CODE CAUSE AND/OR PROCEDURE FOR CORRECTION
U01721
A communication error occurred during transmission at high transmission speed. The destination party’s fax may not have
the corresponding high speed reception capabilities. If the destination party’s fax number was dialed using an abbreviated
number or one-touch key, change the transmission speed registered for that number to a lower setting and perform
transmission procedures again.
U01800 -
U01820 A communication error occurred during reception at high transmission speed. Perform reception procedures again after
having the transmitting party lower the transmission speed.
U01821
A communication error occurred during reception at high transmission speed. Your unit may not have the corresponding
high speed reception capabilities. Perform reception procedures again after having the transmitting party lower the
transmission speed.
U02200
An F-Code Based Relay Broadcast Transmission command was received, but transmission to the remaining final
destination(s) was impossible because the destination fax phone number(s) that was(were) registered for the
corresponding F-Code Relay Box in your fax machine has(have) been deleted. Check the information registered in your fax
and have the initial transmitting station perform the transmission operation again.
U02400
An F-Code Based Relay Broadcast Transmission command was received, but was unsuccessful because the F-Code
Based Relay Box ID that the initial transmitting station entered did not match the one registered in your fax. Check the
information registered in your fax and have the initial transmitting station perform the transmission operation again.
U03000
Polling reception was attempted, but was unsuccessful because no documents had been placed in advance in the
transmitting party’s fax. Check with the transmitting party.
U03200
The transmitting party’s fax is one of our models and an F-Code Based Bulletin Board Reception was attempted in order to
receive documents from that party’s F-Code Box, but was unsuccessful because there were no documents stored in the
corresponding F-Code Box.
An error has occured due to one of the following reasons. Check with the other party.
1 A Polling Reception was attempted in order to receive documents from the other party’s fax, but was unsuccessful
because Password Check Communication was turned ON in the other party’s fax and the necessary password did not
match.
2 The transmitting party’s fax is one of our models and an F-Code Based Bulletin Board Reception was attempted in order
to receive documents from that party’s F-Code Box, but was unsuccessful because Password Check Communication
was turned ON in the other party’s fax and the necessary password did not match.
U03400
Polling reception was attempted, but was unsuccessful because the password input in the transmitting party’s fax and the
self-station ID of the receiving party did not match. Check with the other party.
The transmitting party’s fax is one of our models and an F-Code Based Bulletin Board Reception was attempted in order to
receive documents from that party’s F-Code Box, but was unsuccessful because the F-Code Box number that you entered
was not registered in the other party’s fax.
The transmitting party’s fax is one of our models and an F-Code Based Bulletin Board Reception was attempted in order to
receive documents from that party’s F-Code Box, but was unsuccessful because the F-Code password that you entered did
not match the one registered in the transmitting party’s fax.
An F-Code Based Bulletin Board Reception was attempted in order to receive documents from the other party, but was
unsuccessful because the other party’s fax does not have F-Code Based Bulletin Board Transmission capabilities or
because there were no documents stored in the corresponding box.
The destination fax is one of our models and an F-Code Based Confidential Transmission was attempted in order to
transmit documents to that party’s F-Code Box, but was unsuccessful because the F-Code Box number that you entered
was not registered in the destination party’s fax.
A transmission to a destination party’s box (ex. F-Code Box) was attempted, but was unsuccessful because the destination
party’s fax does not have F-Code Based Confidential Reception capabilities.
Encryption transmission was attempted, but was unsuccessful because the specified destination Confidential Box was not
designated for encryption reception or was not registered in the other party’s fax.
Encryption transmission was attempted, but was unsuccessful because the other party’s fax does not possess Encryption
Communication capabilities.
Encryption Transmission was attempted, but was unsuccessful because the Encryption Keys did not match.