Industrial pc | parameter setting & configuration – Lenze PC-based Automation Industrial PC User Manual
Page 222
Industrial PC | Parameter setting & configuration
Index
222
L
2.5 EN - 01/2012
Rx error counter - port 2 (C1096/26)
Rx error counter - port 2 (C1596/26)
Rx error counter - port 3 (C1096/27)
Rx error counter - port 3 (C1596/27)
Serial number (C1096/5)
Serial number (C1596/5)
Slave address (C1095/2)
Slave address (C1595/2)
Slave addressing mode (C1095/1)
Slave addressing mode (C1595/1)
Slave device name (C1096/6)
Slave device name (C1596/6)
Slave manufacturer ID (C1096/2)
Slave manufacturer ID (C1596/2)
Valid entry (C1096/1)
Valid entry (C1596/1)
ECAT bus
Numb. slaves (C1086/3)
Numb. slaves (C1586/3)
Numb. slaves with DC (C1586/4)
ECAT bus scan
Result (C1080/4)
Result (C1580/4)
ECAT bus scan (C1081/6)
ECAT bus scan (C1581/6)
ECAT config.
Checksum CRC-32 (C1086/2)
Checksum CRC-32 (C1586/2)
No. of slaves (C1086/5)
No. of slaves (C1586/5)
Numb. mailbox slaves (C1586/6)
Number of mailbox slaves (C1086/6)
Physical address (C1096/9)
Physical address (C1596/9)
ECAT counter
Acyclic datagrams (C1086/13)
Acyclic datagrams (C1586/13)
Acyclic frames (C1086/12)
Acyclic frames (C1586/12)
Cyclic datagrams (C1086/11)
Cyclic datagrams (C1586/11)
Cyclic frames (C1086/10)
Cyclic frames (C1586/10)
Lost frames (C1086/9)
Lost frames (C1586/9)
Rx frames (C1086/8)
Rx frames (C1586/8)
Tx frames (C1086/7)
Tx frames (C1586/7)
ECAT DC
Current deviation (C1082/3)
Current deviation (C1582/3)
Perm. dev. slave sync (C1082/2)
Perm. dev. slave sync (C1582/2)
State (C1082/1)
State (C1582/1)
ECAT master
State (C1581/2)
State C1081/2
State information (C1081/5)
State information (C1581/5)
ECAT master config.
Checksum (C1080/2)
Checksum (C1580/2)
Date (C1080/1)
Date (C1580/1)
ECAT master in requested state (C1081/3)
ECAT master in requested state (C1581/3)
ECAT slaves in requested state (C1081/4)
ECAT slaves in requested state (C1581/4)
ECAT stack
Master checksum (C1080/3)
Master checksum (C1580/3)
ECAT state
State change (C1581/1)
State change C1081/1
ECATBus
Numb. slaves with DC (C1086/4)
E-mail to Lenze
Enable Dhcp (C240)
Entering the IP address
Error counter (C1093)
Error counter (C1133)
Error counter (C1593)
Error counter (C1633)
F
Feedback to Lenze
FTP
Allow "Anonymous" (C172)
Allow "Anonymous" upload (C173)
Enabled (C174)
Home user 1 (C105)
Home user 10 (C168)
Home user 2 (C112)
Home user 3 (C119)
Home user 4 (C126)
Home user 5 (C133)
Home user 6 (C140)
Home user 7 (C147)
Home user 8 (C154)
Home user 9 (C161)
Permissions user 1 (C104)
Permissions user 10 (C167)
Permissions user 2 (C111)
Permissions user 3 (C118)
Permissions user 4 (C125)
Permissions user 5 (C132)
Permissions user 6 (C139)
Permissions user 7 (C146)
Permissions user 8 (C153)
Permissions user 9 (C160)
Use authentication (C171)