HP MPX200 Multifunction Router - Manual (Page 92)

This command requires router firmware version 3.3.0.0 or later for scrubbing LUNs and
thin-provisioned destination LUNs.
If the specified source or destination keyword matches more that one array, the command fails
because there can be only one source array and one destination array.
Keywords
Specifies the WWPN of the source storage array. -array_wwpn=
Specifies the Fibre Channel target WWPN of the source storage array. -array_with_fc_target=
Specifies the iSCSI target name of the source storage array. -array_with_is_target=
Specifies the WWULN, T10, NAA, EUI, or Page 0x80 serial number of the source
storage array LUN. -array_with_lun_any_wwuln=
Specifies the EUI of the source storage array LUN. -array_with_lun_eui=
1
Specifies the NAA of the source storage array LUN. -array_with_lun_naa=
1
Specifies the Page 0x80 serial number of the source storage array LUN. -array_with_lun_serial=
1
Specifies the T10 designator of the source storage array LUN. -array_with_lun_tten=
1
Specifies the WWULN of the source storage array LUN. -array_with_lun_wwuln=
1
Specifies the symbolic name of the source storage array. -array_with_name=
Specifies the name of a data migration job. -description=
If this keyword is not used, a default description is created based on the source and
destination LUNs.
Specifies the WWPN of the destination storage array. -dmdest_array_wwpn=
Specifies the WWULN, T10, NAA, EUI, or Page 0x80 serial number of the
destination storage array LUN. -dmdest_array_with_lun_any_wwuln=
Specifies the Fibre Channel target WWPN of the destination storage array. -dmdest_array_with_fc_target=
Specifies the iSCSI target of the destination storage array. -dmdest_array_with_is_target=
Specifies the EUI of the destination storage array LUN. -dmdest_array_with_lun_eui=
2
Specifies the NAA of the destination storage array LUN. -dmdest_array_with_lun_naa=
2
Specifies the Page 0x80 serial number of the destination storage array LUN. -dmdest_array_with_lun_serial=
2
Specifies the T10 designation of the destination storage array LUN. -dmdest_array_with_lun_tten=
2
Specifies the WWPN of the destination storage array LUN. -dmdest_array_with_lun_wwuln=
2
Specifies the symbolic name of the destination storage array. -dmdest_array_with_name=
Specifies the destination array as a WWPN. -dmdest_array_wwpn=
Specifies the destination array as a Fibre Channel target. -dmdest_fc_target=
Specifies the destination array as an iSCSI target. -dmdest_is_target
Accepts the destination LUN name in a variety of formats that are interpreted first
as WWULN, and then as the T10, NAA, EUI, and Page 0x80 serial number
designator until at least one LUN is found. -dmdest_lun_any_wwuln=
Specifies the destination LUN EUI. -dmdest_lun_eui=
3
Specifies the destination LUN NAA designator. -dmdest_lun_naa=
Specifies the destination LUN. -dmdest_lun_number=
Specifies the destination LUN Page 0x80 serial number. -dmdest_lun_serial=
3
Specifies the destination LUN starting block for a partial LUN migration. -dmdest_lun_start_lba=
Specifies the destination LUN T10 designator. -dmdest_lun_tten=
3
Specifies the destination LUN WWULN. -dmdest_lun_wwuln=
3
92 Data Migration commands