Ac-ap tunnel dual-link configuration example, Network requirements – H3C Technologies H3C WX3000E Series Wireless Switches User Manual
Page 49
37
[AC] wlan service-template 1 clear
[AC-wlan-st-1] ssid service
[AC-wlan-st-1] bind WLAN-ESS 1
[AC-wlan-st-1] authentication-method open-system
[AC-wlan-st-1] service-template enable
[AC-wlan-st-1] quit
# Configure a radio policy (the default radio policy default_rp will be used if you don't want to
configure a new radio policy for customizing related parameters).
[AC] wlan radio-policy radpolicy1
[AC-wlan-rp-radpolicy1] beacon-interval 200
[AC-wlan-rp-radpolicy1] dtim 4
[AC-wlan-rp-radpolicy1] rts-threshold 2300
[AC-wlan-rp-radpolicy1] fragment-threshold 2200
[AC-wlan-rp-radpolicy1] short-retry threshold 6
[AC-wlan-rp-radpolicy1] long-retry threshold 5
[AC-wlan-rp-radpolicy1] max-rx-duration 500
[AC-wlan-rp-radpolicy1] quit
# Configure the AP auto configuration feature.
[AC] wlan auto-ap enable
# Configure a common AP for model WA2100 (For each AP model, one common auto AP
configuration is required).
[AC] wlan ap ap1 model WA2100
[AC-wlan-ap-ap1] serial-id auto
# Configure the radio of the common AP, set the maximum power to 10, and automatic channel
is adopted by default.
[AC-wlan-ap-ap1] radio 1 type dot11a
[AC-wlan-ap-ap1-radio-1] max-power 10
# Bind radio policy radiopolicy1 to radio 1, and bind service template 1 to radio 1.
[AC-wlan-ap-ap1-radio-1] radio-policy radiopolicy1
[AC-wlan-ap-ap1-radio-1] service-template 1
[AC-wlan-ap-ap1-radio-1] radio enable
2.
Verify the configuration:
{
You can use the display wlan ap command to view the two APs, and can use the wlan auto-ap
persistent command to convert the two auto APs to configured APs.
{
The clients can associate with the APs and access the WLAN.
AC-AP tunnel dual-link configuration example
Network requirements
As shown in
, AC 1 and AC 2 are connected to a L2 switch. An AP is connected to AC 1 and
AC 2 through the L2 switch. AC 1, AC 2 and the AP are in the same network. The AP gets its IP address
from the DHCP server. The IP address of AC1 is 10.18.1.1 and the IP address of AC 2 is 10.18.1.2. AC 1
is working in master mode and AC2 is working in subordinate mode. When AC 2 detects AC 1 is down,
AC 2 will convert its work mode from subordinate to master. The AP which is connected to AC 2 through
a subordinate tunnel will transform the tunnel mode to master and use AC 2 as the master AC.
- H3C WX5500E Series Access Controllers H3C WX3500E Series Access Controllers H3C WX2500E Series Access Controllers H3C WX6000 Series Access Controllers H3C WX5000 Series Access Controllers H3C WX3000 Series Unified Switches H3C LSWM1WCM10 Access Controller Module H3C LSUM3WCMD0 Access Controller Module H3C LSUM1WCME0 Access Controller Module H3C LSWM1WCM20 Access Controller Module H3C LSQM1WCMB0 Access Controller Module H3C LSRM1WCM2A1 Access Controller Module H3C LSBM1WCM2A0 Access Controller Module H3C WA3600 Series Access Points H3C WA2600 Series WLAN Access Points