H3C Technologies H3C WX3000E Series Wireless Switches User Manual
Page 167
155
Step Command
Remarks
3.
Enable WMM.
wmm enable
By default, WMM is enabled.
The 802.11n protocol stipulates
that all 802.11n clients support
WLAN QoS. Therefore, when the
radio operates in 802.11an or
802.11gn mode, you should
enable WMM. Otherwise, the
associated 802.11n clients may
fail to communicate.
4.
Set the EDCA parameters of
AC-VO or AC-VI queues for
clients.
wmm edca client { ac-vo | ac-vi }
{ aifsn aifsn-value | ecw ecwmin
ecwmin-value ecwmax ecwmax
-value | txoplimit txoplimit-value |
cac } *
Optional.
By default, a client uses the default
5.
Set the EDCA parameters of
AC-BE or AC-BK queues for
clients.
wmm edca client { ac-be | ac-bk }
{ aifsn aifsn-value | ecw ecwmin
ecwmin-value ecwmax ecwmax
-value | txoplimit txoplimit -value } *
Optional.
By default, a client uses the default
EDCA parameters shown in
6.
Set the EDCA parameters and
specify the ACK policy for the
AP radio.
wmm edca radio { ac-vo | ac-vi |
ac-be | ac-bk } { aifsn aifsn-value |
ecw ecwmin ecwmin-value ecwmax
ecwmax -value | txoplimit txoplimit
-value | noack } *
Optional.
By default, an AP radio uses the
default EDCA parameters shown
in
ACK policy.
7.
Set the CAC policy.
wmm cac policy { channelutilization
[ channelutilization-value ] | users
[ users-number ] }
Optional.
By default, the users-based
admission policy applies, with the
maximum number of users being
20.
8.
Map SVP packets to a
specified AC queue.
wmm svp map-ac { ac-vi | ac-vo |
ac-be | ac-bk }
Optional.
By default, the SVP packet
mapping function is disabled.
Note that SVP packet mapping
applies to non WMM clients, and
does not take effect on WMM
clients.
NOTE:
•
If CAC is enabled for an AC queue, CAC is also enabled for the AC queues with higher priority. For
example, if you use the wmm edca client command to enable CAC for the AC-VI queue, CAC is also
enabled for the AC-VO queue. However, enabling CAC for the AC-VO queue does not enable CAC for
the AC-VI queue.
•
H3C recommends that you use the default EDCA parameter settings for APs and clients (except the
TXOPLimit parameter for devices using 802.11b radio cards) unless it is necessary to modify the default
settings.
•
When the radio card of a device is 802.11b, H3C recommends that you set the TXOPLimit values of the
AC-BK, AC-BE, AC-VI, and AC-VO queues to 0, 0, 188, and 102 respectively.
•
The SVP packet mapping function takes effect only after you enable WMM.
- H3C WX5500E Series Access Controllers H3C WX3500E Series Access Controllers H3C WX2500E Series Access Controllers H3C WX6000 Series Access Controllers H3C WX5000 Series Access Controllers H3C WX3000 Series Unified Switches H3C LSWM1WCM10 Access Controller Module H3C LSUM3WCMD0 Access Controller Module H3C LSUM1WCME0 Access Controller Module H3C LSWM1WCM20 Access Controller Module H3C LSQM1WCMB0 Access Controller Module H3C LSRM1WCM2A1 Access Controller Module H3C LSBM1WCM2A0 Access Controller Module H3C WA3600 Series Access Points H3C WA2600 Series WLAN Access Points