Comtech EF Data CDM-710G - Manual (Page 195)

CDM-710G High-Speed Satellite Modem Revision 1
Remote Control MN-CDM710G
A–5
A.6 Remote Commands and Queries
Index Notes: Column ‘C’ = Command; Column ‘Q’ = Query; columns marked ‘X’ designate instruction code as Command only, Query only, Command/Query.
CODE C Q PAGE CODE C Q PAGE CODE C Q PAGE CODE C Q PAGE CODE C Q PAGE
A G M RGS X X A-25, A-41 TMD X X A-6, A-27
AEQ X X A-16, A-33 MAC X A-16, A-21, A-38 RIE X X A-25, A-41 TMP X A-14, A-27, A-42
GIP X X A-7, A-20, A-37 MGC X X A-43 RMD X X A-15, A-33 TPI X X A-14, A-31
B GMC X A-20, A-28 MSK X X A-11, A-22 RNE X A-11, A-25, A-41 TPL X X A-14, A-32
BFS X A-16, A-28 GSW X A-20, A-28 RPI X X A-25, A-41 TSI X X A-14, A-32
BTH A-16 N RSL X A-26, A-42 TSR X X A-6, A-27
C H NUE X A-17, A-22, A-39 RSR X X A-16, A-33 TST X X A-14, A-43
CAE X A-6, A-16, A-34 RSW X X A-26, A-42 TXO X X A-15, A-32
CID X X A-6, A-16, A-34 O
CLD X A-6, A-16, A-34 U
CST X A-7, A-17, A-34 I P S
IEP X A-7, A-20, A-37 SCX X X A-12, A-26, A-42
D IMG X A-7, A-20, A-37 Q SLM X X A-12, A-26, A-42 V
DAY X X A-7, A-17, A-34 IMP X X A-8, A-20, A-29 SNO X A-12, A-26, A-42
DLK X A-17, A-34 IPA X X A-8, A-21, A-38 R SWR X A-12, A-26, A-42
IPG X X A-10, A-21, A-38 RAR X X A-22, A-39 W
E ITF X A-10, A-21, A-38 RBS X X A-22, A-29, A-39 T
EBA X X A-18, A-34 RBT X A-11, A-23, A-39 TAR X X A-12, A-30
EBN X A-18, A-34 RCB X A-23, A-29 TCI X X A-12, A-30 X
EFI X X A-19, A-28 J RCI X X A-23, A-39 TCR X X A-6, A-27
EID X A-8, A-18 RCK X X A-23, A-29 TDI X X A-13, A-30
ERF X X A-10, A-19, A-37 RCR X X A-15, A-33 TDR X A-13, A-30 Y
ESN X A-19, A-37 K RDI X X A-23, A-39 TFQ X X A-13, A-30
ESW X X A-7, A-19, A-37 RDR X A-23, A-40 TFS X X A-13, A-30
ETS X X A-20, A-28 RED X X A-12, A-24, A-40 TFT X A-13, A-31 Z
L RFM X X A-24, A-29 TGS X X A-13, A-31
F LNK X A-21, A-38 RFO X A-24, A-40 TIE X X A-13, A-31
FLT X A-9, A-30, A-35 LRS X X A-10, A-21, A-38 RFQ X X A-24, A-40 TIM X X A-14, A-26, A-42
FRW X A-7, A-19, A-37 RFS X A-24, A-40 TLC X X A-26, A-31
RFT X A-25, A-40 TLP X X A-14, A-31
Note: In the tabulature that follows, the following codes are used in the ‘Response to Command’ column (as per Sect. A.5.4 Instruction Code Qualifier):
= Message ok
? Received ok, but invalid arguments found
* Message ok, but not permitted in current mode
# Message ok, but unit is not in Remote mode