Dwyer UXF3 - Manual (Page 8)

-vi-
4.11.8. How to set the ID No. ···································· 78
4.11.9. How to confirm the software version ············· 78
4.11.10. Initializing setting parameters ······················ 79
4.11.11. How to set the detailed setting····················· 80
5. Mounting of detector ···················································· 82
5.1. Detector mounting procedure ································ 82
5.1.1. Mounting of detector ······································· 83
5.1.2. Image figure of mounting dimension ··············· 83
5.2. Selection of mounting position······························· 84
5.3. Selection of mounting method ······························· 85
5.4. Processing of mounting surface ···························· 86
5.5. How to determine the mounting position ··············· 87
5.6. Selection of acoustic couplant ······························· 88
5.7. Cable end treatment ·············································· 89
5.7.1. Cable end treatment for SX2··························· 89
5.7.2. Cable end treatment for SX1··························· 89
5.8. Reserved for Future Use ······································· 90
5.8.1. Reserved························································· 90
5.8.2. Reserved························································· 90
5.9. Mounting small-diameter and medium size
sensor (SX1) ··················································· 91
5.9.1. Connection of sensor cable····························· 91
5.9.2. Assembly procedure of the sensor ·················· 93
5.9.3. Mounting method on the pipe·························· 94
5.9.3.1. In case of V method·································· 94
5.9.3.2. In case of Z method·································· 96
5.10. Mounting large size detector (SX1) ····················· 97
5.10.1. Connection of sensor cable··························· 97
5.10.2. Mounting method on the pipe························ 98
5.11. Mounting small diameter detector (SX2)·············· 99
5.12. Mounting high temperature detector (SX2)········ 100
5.12.1. Mounting of detector (in case of V method) 100
5.12.2. Mounting of detector (in case of Z method)· 101
6. CHECK AND MAINTENANCE ··································· 102
6.1. Daily Check ························································· 102
6.2. Periodic Inspection ·············································· 102
6.2.1. Checking zero point ······································ 102
6.2.2. Reapplying grease ········································ 102
6.2.3. How to measure the insulation resistance····· 103
6.2.3.1. Flow transmitter : UXF3·························· 103
6.2.3.2. Reserved ················································ 104
6.3. How to replace the fuse······································· 105
6.3.1. Flow transmitter : UXF3 ································ 105
6.3.2. Reserved······················································· 106
6.4. How to replace the relay ······································ 107
6.4.1. Flow transmitter : UXF3 ································ 107
6.4.2. Reserved······················································· 108
6.5. How to replace the LCD ······································ 109
6.5.1. Flow transmitter : UXF3 ································ 109
6.5.2. Reserved························································110
6.6. ERROR AND REMEDY ········································110
6.6.1. Display error···················································111
6.6.1.1. Checking the LCD/LED ··························· 111
6.6.1.2. Checking the LED lit in red ······················112
6.6.1.3. Checking the RAS information ················113
6.6.2. Displaying the data in maintenance mode ·····114
6.6.3. Keying is abnormal ········································115
6.6.4. Error in measured value·································116
6.6.5. Error in analog output ····································118
6.6.6. Checking received waveforms ·······················119
6.6.6.1. How to connect the oscilloscope ·············119
6.6.6.2. Checking sending/receiving···················· 120
6.6.7. Remedying a hardware fault ····················· 122
7. Appendix ···································································· 123
7.1. How to make gauge paper ·································· 123
7.2. Piping data ·························································· 124
Bulletin F-107-UXF3