AMETEK Compact i/iX Series Software Manual - Manual (Page 198)

User Manual – Rev H California Instruments
Avionics Software 198
TVF501 Power Failure Test requires physically removing line cables Test not performed with software
8.4.1.3 Table SCF:
Test No. Section Subject Test Limits Comment File Ref.
SCF101 Steady State Voltage and Frequency 104 to 122 Volts RMS
DO160 16.5.1.1.b, 410Hz and
390Hz
SCF101
SCF102 Voltage Transients Surge to 160Vac max, Sag to 71Vac min DO160 16.5.1.5.1.b, 400Hz SCF102
SCF103 Voltage Modulation Vamp = 0.18V to 1.24V, Mrate = 1Hz to 200Hz DO160 16.5.1.2, 400Hz SCF103
SCF104 Voltage Spikes Requires Additional Equipment
SCF105 Current Distortion 115Vnom, 400 Hz Limits defined by Table A.4 SCF105
SCF106 Voltage Distortion 10% distortion 30sec each frequency SCF106
SCF106 EW Voltage Distortion - Endurance test with motor 10% distortion Per Table SCF 106-2 SCF106-EW
SCF106 E
Voltage Distortion - Endurance test without
motor
10% distortion Per Table SCF 106-2 SCF106-E
SCF107 Inrush Current Test requires multiple load cables Test not performed with software
SCF108 Frequency Modulation
Famp = 4.9 Hz to 0.2Hz, Mrate = 0.014Hz to
100Hz
DO160 16.5.1.3, 400Hz SCF108
SCF109 Voltage DC Content +/-.3VDC Offset 30 mins each test SCF109
SCF110 Voltage Modulation due to Equipment Test requires special cables Test not performed with software
SCF111
Voltage Spike Due to Equipment Load
Switching
Requires Additional Equipment
SCF201 Abnormal Steady State Voltage and Frequency 96 to 130 Volts RMS DO160 16.5.2.1.b, 400Hz SCF201
SCF202 Abnormal Voltage Transients Surge to 180Vac max, Sag to 0Vac min DO160 16.5.2.2.b, 400Hz SCF202
SCF203 Abnormal Voltage Modulation Vamp = 0.18V to 1.24V, Mrate = 1Hz to 200Hz DO160 16.5.1.2, 400Hz SCF203
SCF204 Abnormal Frequency Variations 320Hz to 480Hz SCF204
SCF401 Transparency Time 10ms dropouts Per Figure SCF 401-1 SCF401
SCF402 Voltage Switching Transients 1 Test Conditions 1-17, 400Hz Per Figure SCF 402-1 SCF402-1
SCF402 Voltage Switching Transients 1 Test Conditions 18-27, 400Hz Per Figure SCF 402-1 SCF402-2
SCF402 Voltage Switching Transients 1 Test Conditions 28-36, 400Hz Per Figure SCF 402-1 SCF402-3
SCF402 Voltage Switching Transients 1 Test Conditions 37-42, 400Hz Per Figure SCF 402-1 SCF402-4
SCF403 Voltage Switching Transients 2 T=1 to T=49, 400Hz Per Figure SCF 403-1 SCF403-1
SCF403 Voltage Switching Transients 2 T=50 to T=99, 400Hz Per Figure SCF 403-1 SCF403-2
SCF403 Voltage Switching Transients 2 T=100 to T=200, 400Hz Per Figure SCF 403-1 SCF403-3
SCF501 Power Failure Test requires physically removing line cables Test not performed with software