AMETEK Compact i/iX Series Software Manual - Manual (Page 196)

User Manual – Rev H California Instruments
Avionics Software 196
SVF401 Transparency Time 10ms dropouts Per Figure SVF 401-1 SVF401
SVF402 Voltage Switching Transients 1 Test Conditions 1-17, 390Hz Per Figure SVF 402-1 SVF402-1
SVF402 Voltage Switching Transients 1 Test Conditions 18-27, 390Hz Per Figure SVF 402-1 SVF402-2
SVF402 Voltage Switching Transients 1 Test Conditions 28-36, 390Hz Per Figure SVF 402-1 SVF402-3
SVF402 Voltage Switching Transients 1 Test Conditions 37-42, 390Hz Per Figure SVF 402-1 SVF402-4
SVF402 Voltage Switching Transients 1 Test Conditions 1-17, 620Hz Per Figure SVF 402-1 SVF402-5
SVF402 Voltage Switching Transients 1 Test Conditions 18-27, 620Hz Per Figure SVF 402-1 SVF402-6
SVF402 Voltage Switching Transients 1 Test Conditions 28-36, 620Hz Per Figure SVF 402-1 SVF402-7
SVF402 Voltage Switching Transients 1 Test Conditions 37-42, 620Hz Per Figure SVF 402-1 SVF402-8
SVF403 Voltage Switching Transients 2 T=1 to T=49, 620Hz Per Figure SVF 403-1 SVF403-1
SVF403 Voltage Switching Transients 2 T=50 to T=99, 620Hz Per Figure SVF 403-1 SVF403-2
SVF403 Voltage Switching Transients 2 T=100 to T=200, 620Hz Per Figure SVF 403-1 SVF403-3
SVF403 Voltage Switching Transients 2 T=1 to T=49, 390Hz Per Figure SVF 403-1 SVF403-4
SVF403 Voltage Switching Transients 2 T=50 to T=99, 390Hz Per Figure SVF 403-1 SVF403-5
SVF403 Voltage Switching Transients 2 T=100 to T=200, 390Hz Per Figure SVF 403-1 SVF403-6
SVF404
Voltage Switching Transients with Frequency
Change
50-200ms dropouts Per Figure SVF 404-1 SVF404
SVF501 Power Failure Test requires physically removing line cables Test not performed with software
8.4.1.2 Table TVF:
Test No. Section Subject Test Limits Comment File Ref.
TVF101 Steady State Voltage and Frequency 104 to 122 Volts RMS
DO160 16.5.1.1.b, 620Hz and
390Hz
TVF101
TVF102 Voltage Transients Surge to 160Vac max, Sag to 71Vac min
DO160 16.5.1.5.1.b, 620Hz and
390Hz
TVF102
TVF103 Voltage Modulation Vamp = 0.18V to 1.24V, Mrate = 1Hz to 200Hz DO160 16.5.1.2, 620Hz and 390Hz TVF103
TVF104 Voltage Spikes Requires Additional Equipment
TVF105 Current Distortion 115Vnom, 390-620 Hz Limits defined by Table A.5 TVF105
TVF106 Voltage Distortion 10% distortion 30sec each frequency TVF106
TVF106 EW Voltage Distortion - Endurance test with motor 10% distortion Per Table TVF 106-2 TVF106-EW
TVF106 E Voltage Distortion - Endurance test without motor 10% distortion Per Table TVF 106-2 TVF106-E
TVF107 Inrush Current Test requires multiple load cables Test not performed with software
TVF108 Frequency Variations Slew from 390 to 620Hz, 100Hz/s up and down 3 times each TVF108
TVF109 Frequency Modulation
Famp = 4.9 Hz to 0.2Hz, Mrate = 0.014Hz to
100Hz
DO160 16.5.1.3, 620Hz and 390Hz TVF109