Cub Cadet SLTX1000 Series User Manual
3urihvvlrqdo6krs0dqxdo
3URIHVVLRQDO6KRS0DQXDO
3URIHVVLRQDO6KRS0DQXDO
LTX Series Riding Tractors
NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power
equipment of the kind described in this publication, and are not intended for use by untrained or inexperienced individuals.
These materials are intended to provide supplemental information to assist the trained technician. Untrained or inexperi-
enced individuals should seek the assistance of an experienced and trained professional. Read, understand, and follow all
instructions and use common sense when working on power equipment. This includes the contents of the product’s Oper-
ators Manual, supplied with the equipment. No liability can be accepted for any inaccuracies or omission in this publication,
although care has been taken to make it as complete and accurate as possible at the time of publication. However, due to
the variety of outdoor power equipment and continuing product changes that occur over time, updates will be made to these
instructions from time to time. Therefore, it may be necessary to obtain the latest materials before servicing or repairing a
product. The company reserves the right to make changes at any time to this publication without prior notice and without
incurring an obligation to make such changes to previously published versions. Instructions, photographs and illustrations
used in this publication are for reference use only and may not depict actual model and component parts.
© Copyright 2012 MTD Products Inc. All Rights Reserved
Document Outline
- Chapter 1: Introduction
- Chapter 2: Engine related parts
- Chapter 3A: Steering
- Chapter 3B: Electronic Power Steering
- Chapter 4: Body panels
- Chapter 5: Hydro. Drive and brake system
- About this chapter
- Externally repairable drive system problems
- Indications that a transaxle is not warrantable
- Brake adjustment
- Neutral control adjustment
- Linkage: pedal shaft
- Pedal shaft assembly removal
- Belt control; tensioner and idler pulleys
- Drive belt replacement
- Changing transaxle hydraulic fluid
- Brakes
- Transaxle removal and replacement
- Chapter 6: CVT Drive and brake system
- About this chapter
- About the variable speed drive system.
- Externally repairable drive system problems:
- Indications that a transaxle is not warrantable
- Brake adjustment
- Gear selector
- Tensioner pulley control rod
- Linkage: pedal shaft
- Pedal shaft assembly removal:
- Linkage: pedal tie strap
- Belt control: tension make-up pulley
- Belt control: variable speed pulley
- Belt control: tensioner pulleys
- Drive belt replacement
- Transaxle removal and replacement
- Transaxle repair
- Chapter 7: electrical system
- Introduction
- RMC Module
- Key switch
- RMC Module
- RMC module plug test (electric PTO)
- RMC module plug test (manual PTO)
- Electric PTO switch
- PTO relay
- PTO switch (manual PTO)
- Brake switch (manual PTO)
- Brake switch (electric PTO)
- Park brake switch
- Reverse Safety Switch
- Seat Safety Switch
- Starter solenoid
- Start Circuit
- Run Circuit
- Run Circuit / Reverse Caution mode
- Engine shutdown circuits
- Charging circuit
- PTO Circuit (electric PTO)
- Reverse Mower Control (RMC) circuit operation
- Electrical diagnosis
- Electronics
- Electrical environment: AC Vs. DC
- Ohm’s Law
- Kirchhoff’s current law
- Kirchhoff’s voltage law
- How the system is wired together
- Types of circuits
- Series
- Parallel
- Series/parallel
- Shorts
- Opens
- Increased resistance
- The Tools
- Digital multimeter
- Wiring diagram or schematic
- Fused jumper wires
- Test lights
- Self-powered continuity lights
- Ammeters and specialized charging system testers
- Batteries
- Charging the battery
- Checking battery condition
- Battery Testers
- Adjustable load testers
- Fixed load testers
- Conductance testers
- Battery discharge test
- Storage of batteries
- Electrical Troubleshooting
- Voltage Drop Test
- Testing switches
- Diodes
- Relay
- Schematics
- Chapter 8: Cutting Decks and lift shaft
- Chapter 9: Maintenance intervals
- Hydro-gear Appendix