Metrohm 799 GPT Titrino - Manual (Page 141)

3.2 Remote control commands
799 GPT Titrino
137
"Info", continuation
│ ├ .EP Endpoint
│ │ ├ .1 1 st result
│ │ │ ├ .V Value read only ditto
│ │ │ ├ .Meas Measured value read only
│ │ │ ├ .Mark Mark if more than 1 EP per window read only
│ │ ├ up to 9 EP's
│ ├ .Var Variables C4X
│ │ ├ .C40 Start measured value read only/read+write ditto
│ │ ├ .C41 Titration end volume read only/read+write
│ │ ├ .C42 Titration time read only/read+write
│ │ ├ .C43 Volume drift in SET/KFT read only/read+write
│ │ ├ .C44 Titration temperature read only/read+write
│ │ ├ .C45 Start volume read only/read+write
│ │ ├ .C46 Asymmetry pH read only
│ │ ├ .C47 Slope of electrode read only
│ │ ├ .C48 Volume at maximum voltage read only/read+write
│ │ ├ .C49 Volume at minimum voltage read only/read+write
│ │ ├ .DTime Time for drift corr.or dosing time read only/read+write
│ ├ .FixEP Fix EP or fix volume
│ │ ├ .51 C51
│ │ │ ├ .Value Value read only 3.2.2.136.
│ │ │ up to 59
│ ├ .pK pK/HNP or fix times
│ │ ├ .61 C61
│ │ │ ├ .Value Value read only ditto
│ │ │ up to 69
│ ├ .TempVar Temporary variables C7X
│ │ ├ .C70 up to C79 read only/read+write ditto
│ ├ .TimeWin Rates in time windows
│ │ ├ .81 C81
│ │ │ ├ .Mean Rate read only 3.2.2.137.
│ │ │ ├ .Dev Standard deviation of the rate read only ditto
│ │ │ up to 89
│ ├ .MeanRateC80 Mean rate C80
│ │ ├ .Mean Rate read only ditto
│ │ ├ .Dev Standard deviation of the rate read only ditto
│
├ .StatisticsVal Statistics values
│ ├ .ActN Number of results in chart read only 3.2.2.138.
│ ├ .1 1 st mean
│ │ ├ .Mean Mean read only ditto
│ │ ├ .Std Absolute standard deviation read only ditto
│ │ ├ .RelStd Relative standard deviation read only ditto
│ ├ up to 9 mean values
│
├ .SiloCalc Values of silo calculations
│ ├ .C24 Values of variable C24
│ │ ├ .Name Name read only 3.2.2.139.
│ │ ├ .Value Value read only ditto
│ │ ├ .Unit Unit read only ditto
│ ├ .C25 as for C24
│ ├ .C26 Values of variable C26
│ │ ├ .ActN Number of single values read only ditto
│ │ ├ .Mean Mean value read only ditto
│ │ ├ .Std Absolute standard deviation read only ditto
│ │ ├ .RelStd Relative standard deviation read only ditto
│ ├ .C27 as for C26