Metrohm 799 GPT Titrino - Manual (Page 130)

3.2. Remote control commands
799 GPT Titrino
126
*Parameter Tree part "Parameters for DOC"
├ . DosPara Dosing parameters
│ ├ .BeginMeas Begin of measuring depends on meas.quant. 3.2.2.57.
│ ├ .EndMeas End of measuring depends on meas.quant. ditto
│ ├ .UnitMeas Unit of measured quantity read only ditto
│ ├ .SweepTime Sweep time 0...300...999 999 3.2.2.58.
│ ├ .Dyn Dynamics depends on meas.quant. 3.2.2.59.
│ ├ .UnitDyn Unit of dynamics read only ditto
│ ├ .MaxRate Maximum dosing rate 0.01... 150, max. ditto
│ ├ .MinRate Minimum dosing rate 0.01...5.0...9999 ditto
│ ├ .Direction Direction +, -, auto 3.2.2.60.
│ ├ .StartV Start volume
│ │ ├ .Type Type of start volume abs., rel., OFF 3.2.2.61.
│ │ ├ .V Volume for absolute start volume 0...999.99 ditto
│ │ ├ .Factor Factor for relative start volume 0...±999 999 ditto
│ │ ├ .Rate Dispensing rate for start volume 0.01...150.0, max. ditto
│ ├ .Pause Waiting time after start volume 0...999 999 ditto
│ ├ .TDelta Time interv. for meas.acquisition 1...10...999 999 3.2.2.52.
│ ├ .DosUnit Selection of the dosing unit internal D0, external D1,
│ │ external D2 3.2.2.17.
│ ├ .MeasInput Measuring input 1, 2, diff. 3.2.2.62.
│ ├ .Ipol Polarization current 0...1...±127 ditto
│ ├ .Upol Polarization voltage 0...400...±1270 ditto
│ ├ .PolElectrTest Test for polarized electrodes ON, OFF ditto
│ ├ .Temp Titration temperature -170.0...25.0...500.0 3.2.2.53.
│ │
├ . StopCond Stop conditions
│ ├ .VStop Stop volume
│ │ ├ .Type Type of stop volume abs., rel., OFF 3.2.2.20.
│ │ ├ .V Volume for absolute stop volume 0...99.99...9999.99 ditto
│ │ ├ .Factor Factor for relative stop volume 0...±999 999 ditto
│ ├ .FillRate Filling rate 0.01...150.0, max. 3.2.2.23.
│ │
├
. Statistics Statistics
│ ├ .Status Status of statistics calculation ON, OFF 3.2.2.24.
│ ├ .MeanN No. of individual determinations 2...20 ditto
│ ├ .ResTab Result table
│ │ ├ .Select original,delete n,delete all ditto
│ │ ├ .DelN Deletion of individual results 1...20 ditto
│ │
├ . Monitoring Monitoring
│ ├ .MeasVal Monitoring of measured values
│ │ ├ .Status Status ON, OFF 3.2.2.45.
│ │ ├ .LowLim Lower limit depends on meas.quant. ditto
│ │ ├ .UpLim Upper limit depends on meas.quant. ditto
│ │ ├ .Action Action if out of limits end, hold, wait, none ditto
│ ├ .Temp Monitoring of temperatures
│ │ ├ .Status Status ON, OFF 3.2.2.47.
│ │ ├ .LowLim Lower limit -170.0...500.0 ditto
│ │ ├ .UpLim Upper limit -170.0...500.0 ditto
│ │ ├ .Action Action if out of limits end, hold, wait, none ditto