Metrohm 799 GPT Titrino - Manual (Page 137)

3.2 Remote control commands
799 GPT Titrino
133
├ .RSSet1 Settings RS232, 1 $G 3.2.2.108.
│ ├ .Baud Baud rate 300,600,1200,2400,4800,
│ │ 9600,19200,38400,57600,
│ │ 115200 ditto
│ ├ .DataBit Number of data bits 7, 8 ditto
│ ├ .StopBit Number of stop bits 1, 2 ditto
│ ├ .Parity Parity even, odd, none ditto
│ ├ .Handsh Handshake HWs, SWchar,
│ │ SWline, none ditto
├ .RSSet2 as for RS1
│
├ .ComVar Values of common variables
│ ├ .C30 C30 0... ±999 999 3.2.2.109.
│ ├ up to C39 0... ±999 999
│
├ .DosPrep Parameters for the preparation of burets
│ ├ .PowerOnPrep Warning after power on ON, OFF 3.2.2.110.
│ ├ .Report Preparation report ON, OFF 3.2.2.111.
│ ├ .Select Selection of dosing unit internal D0, external D1,
│ external D2 3.2.2.112.
│ ├ .D0 Internal Titrino buret
│ │ ├ .WarnInterval Warning interval for preparation 5...9999, OFF 3.2.2.113.
│ │ ├ .V Volume 0...3.5...99999.99 3.2.2.114.
│ │ ├ .Repeat Number of cycles 1...2...9 3.2.2.115.
│ │ ├ .DosRate Dosing rate 0.01...150, max. 3.2.2.116.
│ │ ├ .FillRate Filling rate 0.01...150, max. ditto
│ ├ .D1 Buret D1
│ │ ├ .WarnInterval Warning interval for preparation 5...9999, OFF 3.2.2.104.
│ │ ├ .Select Type of dosing unit Dosimat, Dosino 3.2.2.117.
│ │ ├ .Dosimat Parameters for Dosimats
│ │ │ ├ .V Volume 0...3.5...99999.99 3.2.2.107.
│ │ │ ├ .Repeat Number of cycles 1...2...9 3.2.2.108.
│ │ │ ├ .DosRate Dosing rate 0.01...150, max. 3.2.2.109.
│ │ │ ├ .FillRate Filling rate 0.01...150, max. ditto
│ │ ├ .Dosino Parameters for Dosinos
│ │ │ ├ .Outlet Expelling outlet tip, flask 3.2.2.118.
│ │ │ ├ .DosTubing Size of dosing tubes
│ │ │ │ ├ .Length Length 1...40.0...999.9 3.2.2.119.
│ │ │ │ ├ .Diam Diameter 0.1...2.0...9.9 ditto
│ │ │ ├ .AspirTubing Size of aspirating tubes
│ │ │ │ ├ .Length Length 1...25.0...999.9 ditto
│ │ │ │ ├ .Diam Diameter 0.1...2.0...9.9 ditto
│ │ │ ├ .DosRate Dosing rate 0.01...150, max. 3.2.2.120.
│ │ │ ├ .FillRate Filling rate 0.01...150, max. ditto
│ ├ .D2 Buret D2 as for D1