IAI America E-Con - Manual (Page 59)

51
3. X-SEL-J/K/P/Q/JX/KX/PX/QX
(2) Factory-configured parameters
A: X-SEL-K ṅ-ṅ-CC1-ṅ
B: X-SEL-K ṅ-ṅ-CC2-ṅ
C: X-SEL-K
ṅ-ṅ-CC3-ṅ
Set value
No. Parameter name
Input
range
A B C Remarks
1 I/O port assignment type 0 – 20 0 0 0 0: Fixed assignment
1: Automatic assignment (Priority: slot 1 ᫦)
* The ports only in the continuous installation
range from slot 1 are assigned for safety.)
2 Standard I/O fixed assignment time:
Input port start No. (I/O 1)
-1 – 599 -1 -1 -1 0 + (multiples of 8) (Invalid for negative values)
3 Standard I/O fixed assignment time:
Output port start No. (I/O 1)
-1 – 599 -1 -1 -1 300 + (multiples of 8)
(Invalid for negative values)
4 Expansion I/O 1 fixed assignment
time: Input port start No. (I/O 2)
-1 – 599 -1 -1 032 0 + (multiples of 8) (Invalid for negative values)
(Slot next to the standard I/O)
5 Expansion I/O 1 fixed assignment
time: Output port start No. (I/O 2)
-1 – 599 -1 -1 332 300 + (multiples of 8)
(Invalid for negative values)
6 Expansion I/O 2 fixed assignment
time: Input port start No. (I/O 3)
-1 – 599 -1 016 016 0 + (multiples of 8) (Invalid for negative values)
7 Expansion I/O 2 fixed assignment
time: Output port start No. (I/O 3)
-1 – 599 -1 316 316 300 + (multiples of 8)
(Invalid for negative values)
8 Expansion I/O 3 fixed assignment
time: Input port start No. (I/O 4)
-1 – 599 0 0 0 0 + (multiples of 8) (Invalid for negative values)
9 Expansion I/O 3 fixed assignment
time: Output port start No. (I/O 4)
-1 – 599 300 300 300 300 + (multiples of 8)
(Invalid for negative values)
10 Standard I/O error monitoring
(I/O 1)
0 – 5 0 0 0
11 Expansion I/O 1 error monitoring
(I/O 2)
0 – 5 0 0 2
12 Expansion I/O 2 error monitoring
(I/O 3)
0 – 5 0 2 2
13 Expansion I/O 3 error monitoring
(I/O 4)
0 – 5 2 2 2
0: Non-monitoring
1: Monitoring
2: Monitoring (Non-monitoring of 24V I/O power
related errors)
(Main application of Ver. 0.55 or later)
3: Monitoring (Monitoring of 24V I/O power related
errors only)
(Main application of Ver. 0.55 or later)
14 Network I/F card remote: Number of
ports used for input
0 – 256 0 0 0 Multiples of 8
15 Network I/F card remote: Number of
ports used for output
0 – 256 0 0 0 Multiples of 8
(I/O 1) to (I/O 4) indicate the slot numbers.
(Note) When a standard I/O board is not used, it is not required to supply 24V DC to the I/O 24V power connector. In this case,
set the parameter No. 10 to “0.”