Comtech EF Data SNM-1010L - Manual (Page 229)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
ASYNC TX Channel Char. Length
(ref. ‘TCCL_’command).
ASYNC RX Channel Char. Length
(ref. ‘RCCL_’command).
ASYNC TX Channel Stop Bits
(ref. ‘TCSB_’command).
ASYNC RX Channel Stop Bits
(ref. ‘RCSB_’command).
ASYNC TX Channel Parity
(ref. ‘TOCP_’command).
ASYNC RX Channel Parity
(ref. ‘ROCP_’command).
ASYNC TX Communication Type
(ref. ‘TCT_’command).
ASYNC RX Communicatiuon Type
(ref. ‘RCT_’command).
AUPC Local Power Enable ON/OFF
(ref. ‘LPC_’command).
AUPC Nominal Power Value
(ref. ‘NOMP_’command).
AUPC Minimum Power Value
(ref. ‘MINP_’command).
AUPC Max Power Value
(ref. ‘MINP_’command).
AUPC EBNO Target Set Point
(ref. ‘ENSP_’command).
AUPC Max. Tracking Rate
(ref. ‘ENSP_’command).
AUPC Local Carrier Loss
(ref. ‘LCL_’command).
AUPC Remote Carrier Loss
(ref. ‘RCL_’command).
TX BPSK Data Ordering
(ref. ‘TDA_’command).
RX BPSK Data Ordering
(ref. ‘RDA_’command).
RTS TX-IF Control Mode
(ref. ‘RTSM_’command).
CTS Delay Time
p78 = n, where ‘n’ is the current programmed character
length.
p79 = n, where ‘n’ is the current programmed character
length.
p80 = n, where ‘n’ is the current number of stop bits
programmed.
p81 = n, where ‘n’ is the current number of stop bits
programmed.
p82 = xxxx, where ‘xxxx’ is the current programmed
parity.
p83 = xxxx, where ‘xxxx’ is the current programmed
parity.
p84 = n, where ‘n is ‘0’ (RS232), ‘1’ (RS485-4WIRE), ‘2’
(RS485_2WIRE).
p85 = n, where ‘n is ‘0’ (RS232), ‘1’ (RS485-4WIRE), ‘2’
(RS485_2WIRE).
p86 = n, where ‘n’ is ‘0’ (OFF) or ‘1’ (ON).
p87 = snn.n where ‘snn.n’ is Nominal Power value in
dBm.
p88 = snn.n where ‘snn.n’ is Minimum Power value in
dBm.
p89 = snn.n where ‘snn.n’ is Maximum Power value in
dBm.
p90 = nn.n where ‘nn.n’ is EBNO target Set Point in dB.
p91 = n.n where ‘n.n’ is the Max. tracking Rate in dB/Min.
p92 = n, where ‘n’ is ‘0’ (HOLD), ‘1’ (NOMINAL), ‘2’
(MAXIMUM).
p93 =n, where ‘n’ is ‘0’ (HOLD), ‘1’ (NOMINAL), ‘2’
(MAXIMUM).
p94 = n, where, ‘n’ is ‘0’ (NRM), ‘1’ (INV).
p95 = n, where, ‘n’ is ‘0’ (NRM), ‘1’ (INV).
p96 =n, where ‘n’ is ‘0’ )OFF) or ‘1’ (ON).
p97 = nn, where ‘nn’ is CTS delay time in seconds.
A–31