Comtech EF Data SNM-1010L - Manual (Page 214)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
Current TX Reed-
Solomon N/K and
Interleaver Value Status:
Response: MC TXRS_’cr’
TXRS_nnn/kkk_ii’cr’’lf’] Where: nnn = N value, kkk = K value and
ii = Interleaver value.
Scrambler Type Status:
Response: MC SCR_’cr’
SCR_xxxxxxxxxxxx’cr’’lf’] Where: xxxxxxxxx = IBS SYNC, EFD MOD V.35,
INTELSAT V.35, FDC MOD V.35, ITU V.35, or Off.
Demodulator
Configuration Status Status:
Response: MC DCS_'cr'
DCS_'cr'
DF_nnn.nnnn'cr'
DR_nnnn_mmm.mmm'cr'
ADRA_nnnn_mmm.mmm'cr'
ADRB_nnnn_mmm.mmm'cr'
ADRC_nnnn_mmm.mmm'cr'
ADRD_nnnn_mmm.mmm'cr'
ADRV_nnnn.mmm.mmm'cr'
DE_xxx'cr'
DDEC_xxx'cr'
RFL_xxx'cr'
IFL_xxx'cr'
SCF_snnnnn'cr' (Note
1)
SWR_nnnnn'cr' (Note 1)
BERT_xxxx'cr'
DT_xxxx'cr'
DDT_xxx'cr'
RDA_xxx'cr' (Note
1)
RXM_xxxxx'cr'
RSDE_xxx'cr''lf'] (Note
1)
Demodulator Frequency
Demodulator Rate
Preset A Assignment
Preset B Assignment
Preset C Assignment
Preset D Assignment
Preset V Assignment
Descrambler Enable (ON/OFF)
Differential Decoder (ON/OFF)
RF Loopback (ON/OFF)
IF Loopback (ON/OFF)
Sweep Center Frequency
Sweep Width Range
BER Threshold
Demodulator Type
Demodulator Decoder Type
RX BPSK Data Ordering
RX Mode
Reed-Solomon Decoder
The demodulator configuration status command causes
a block of data to be returned by the addressed modem.
The block of data reflects the current configuration of
the demodulator.
Notes:
Status only returned in Receive Continuous mode.
Demodulator/ Decoder
Configuration Program
Status Status:
Response: MC DCP_'cr'
DCP_'cr'
SMT_xxxxxxx’cr’
IROT_xxxxx’cr’
MOM_xxxxxxx'cr'
BERT_xxxx’cr’
DT_xxxx'cr'
DDT_xxx'cr'
DF_nnn.nnnn'cr'
DR_nnnn_mmm.mmm'cr'
DE_xxx'cr'
DENC_xxx'cr'
IFL_xxx’cr’
SCF_snnnnn’cr’
SWR_nnnnn’cr’
SR_xxx’cr’
ILT_xxx’cr’
ERF_nnnnn.n’cr’
BC_xxxx’cr’
RCP_xxxx’cr’
BBL_xxx’cr’
ILB_xxx’cr’
IRFR_xxxx’cr’
IRFR_T1_xxxx’cr’
ICFR_E1_xxxx’cr’
IBP_xxx’cr’
IRE_xxxxxx’cr’
RDF_xxxx’cr’
ISCL_RX1_nnn’cr’
ISCL_RX2_nnn’cr’
System Modem Type
Interface Receive Overhead Type
Modem Operation Mode
BER Threshold
Demodulator Type
Demodulator Decoder Type
Demodulator Frequency
Demodulator Rate
Descrambler Enable (ON/OFF)
Differential Encoder (ON/OFF)
IF Loopback
Sweep Center Frequency
Sweep Width Range
Sweep Reacquisition
Interface Loop Timing
External Reference Frequency
Buffer Clock
RX Clock Phase
Baseband Loopback
Interface Loopback
Interface Coding Format Receive
Interface Receive T1 Frame Structure
Interface Receive E1 Frame Structure
Interface Buffer Program
Interface Read Error (RX 2047)
RX Data Fault
Service Channel Level TX1
Service Channel Level TX2
A–16