Comtech EF Data SNM-1010L - Manual (Page 228)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Receive Mode Selection
(ref. 'RXM_' command).
Not Valid
RS Encoder Enable
(ref. 'RSEN_' command).
RS Decoder Enable
(ref. 'RSDE_' command).
Transmit Data Phase
(ref. ‘TDP_’command).
Receive Data Phase
(ref. ‘RDP_’command).
Drop Data Format
(ref. ‘DDF_’command).
Insert Data Format
(ref. ‘IDF_”command).
Bulk Drop Channels Assignment.
Bulk Insert Channels Assignment.
Insert E1 CRC Enable
(ref. ‘ICRC_’command).
Modem Reference Clock
(ref. ‘MRC_”command).
Mod Spectrum Rotation
(ref. ‘MSR_’command).
Demod Spectrum Rotation
(ref. ‘DSR_’command).
RS Encoder Enable
(ref. ‘RSEN_’command)
RS Decoder Enable
(ref. ‘RSDN_’command)
TX Driver Type
(ref. ‘TXDR_’command).
RX Driver Type
(ref. ‘RXDR_’command).
ASYNC TX Overhead Baud Rate
(ref. ‘TOBR_’command)
ASYNC RX Overhead Baud Rate
(ref. ‘ROBR_’command).
p58 = n, where 'n' is '2' (CONTINUOUS)
p60 = n, where 'n' is '0' (OFF,) or '1' (ON).
p61 = n, where 'n' is '0' (OFF), '1' (ON), or '2'
(CORR_OFF).
p62 = n, where’n’ is ‘0’ (NRM), ‘1’ (INV).
p63 = n where ‘n’ is ‘0’ (NRM), ‘1’ (INV).
p64 = n where ‘n’ is ‘0’ (T1), ‘1’ (T1ESF), ‘2’ (E1CCS),
‘3’ (E1CAS), ‘6’(E131TS), ‘7’ (T1S), and ‘8’ (T1ESFS).
p65 = n, where ‘n’ is ‘0’ (T1), ‘1’ (T1ESF), ‘2’ (E1CCS),
‘3’ (E1CAS), ‘6’ (E131TS), ‘7’ (T1S), and ‘8’ (T1ESFS).
p66 = dd;cc_dd;cc_dd;cc_dd;cc… as defined by the
BDCA_command.
p67 = ii;cc_ii;cc_ii;cc_ii;cc… as defined by the
BDCA_command.
p68 = n, where ‘n’ is 0 (OFF) or ‘1’ (ON).
p69 = n, where ‘n’ is ‘0’ (INT), ‘1’ (EXT1), ‘2’ (EXT5),
‘3’ (EXT10), or ‘4’ (EXT20).
p70 = n, where ‘n’ is ‘0’ (NRM), ‘1’ (INV).
p71 = n, where ‘n’ is ‘0’ (NRM), ‘1’ (INV).
p72 = n, where ‘n’ is 0 (OFF) or ‘1’ (ON).
p73 = n, where ‘n’ is 0 (OFF) or ‘1’ (ON).
p74 = n, where ‘n’ is ‘0’ (G.703), ‘1’ (V.35), ‘2’ (RS422),
‘3’ (RS232).
p75 = n, where ‘n’ is ‘0’ (G.703), ‘1’ (V.35), ‘2’ (RS422),
‘3’ (RS232).
p76 = nnnnn, where ‘nnnnn’ is the current programmed
baud rate.
p77 = nnnnn, where ‘nnnnn’ is the current programmed
baud rate.
A–30