Comtech EF Data SNM-1010L - Manual (Page 213)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
Modulator/
Coder Configuration
Program Status Status:
Response: MC MCP_'cr'
MCP_'cr'
SMT_xxxxxxx’cr’
ITOT_xxxxx’cr’
MOM_xxxxxxx'cr'
MT_xxxx'cr'
MET_xxx'cr'
MF_nnn.nnnn'cr'
MR_nnnn_mmm.mmm'cr'
MPO_snn.n'cr'
MOP_snnn.n'cr'
SE_xxx'cr'
DENC_xxx'cr'
ILT_xxx’cr’
ERF_nnnnn.n’cr’
TC_xxxx’cr’
TCP_xxxx’cr’
BBL_xxx’cr’
ILB_xxx’cr’
ICFT_xxxx’cr’
ISP_xxxxxx’cr’
TDF_xxxx’cr’
ISCL_TX1_nnn’cr’
ISCL_TX2_nnn’cr’
TDP_xxxx’cr’
DDF_xxxxxx’cr’
BDCA_dd;cc-dd;cc…’cr’
MRC_xxx’cr’
MSR_xxx’cr’
RSEN_xxx’cr’
TXDR_xxxxxx’cr’
TOBR_nnnnn’cr’
TCCL_n’cr’
TCSB_n’cr’
TOCP_xxxx’cr’
TCT_xxxxx’cr’
NOMP_snn.n’cr’
MINP_snn.n’cr’
MAXP_snn.n’cr’
LCL_xxxx’cr’
RCL_xxxx’cr’
CTSD_xx’cr’
RTSM_xxx’cr’
TDA_xxx’cr’
COM_xxxxxx’cr’
TRSI_xx’cr’
T310_xxx’cr’
ODU_xxx’cr’
ODUR_xxx’cr’
ODUL_xxx’cr’
ODUH_xxx’cr’
RF_xxx’cr’’lf’]
System Modem Type
Interface Transmit Overhead Type
Modem Operation Mode
Modulator Type
Modulator Encoder Type
Modulator Frequency
Modulator Rate
Modulator Power Offset
Modulator Output Power
Scrambler Enable (ON/OFF)
Differential Encoder (ON/OFF)
Interface Loop Timing
External Reference Frequency
TX Clock (Source)
TX Clock Phase
Baseband Loopback
Interface Loopback
Interface Coding Format Transmit
Interface Substitution Pattern (TX 2047)
TX Data Fault
Service Channel Level TX1
Service Channel Level TX2
TX Data Phase
Drop Data Format
Bulk Drop Channel Assignment
Modulator Reference Clock
Modulator Spectrum Rotation
Reed-Solomon Encoder
TX Driver Type
ASYNC TX Overhead Baud Rate
ASYNC TX Channel Character Length
ASYNC TX Channel Stop Bits
ASYNC TX Overhead Channel Parity
ASYNC TX Communications Type
AUPC Nominal Power Value
AUPC Minimum Power Value
AUPC Maximum Power Value
AUPC Local Carrier Loss
AUPC Remote Carrier Loss
CTS Delay Time
RTS TX Control Mode
TX BPSK Data Ordering
Carrier Only Mode
TX Reed-Solomon Interleave Value
TX 8PSK 2/3 IESS-310 Operation
Outdoor Power
Outdoor Reference
ODU Monitor Low Current Threshold
ODU Monitor High Current Threshold
RF Output (ON/OFF)
This command is used by the Comtech EF Data M:N
protection switch to collect information necessary for
configuring backup modems.
Notes:
1. Status only returned in Transmit
Continuous
mode.
2. Status only returned in Transmit
Burst
mode.
A–15