System commands/responses, A.3.3 system commands/responses – Comtech EF Data SNM-1010L User Manual
Page 209
SNM-1010L Data/Control Modem
Revision 0
Remote Control Channel Commands/Responses
MN/SNM1010L.OM
Receive Data Fault
Command:
Response:
Status:
Response:
MC RDF_xxxx'cr'
RDF_xxxx'cr''lf']
RDF_'cr'
RDF_xxxx'cr''lf']
Where: xxxx = NONE, DATA, or AIS.
Transmit Data Phase
Command:
Response:
Status:
Response:
MC TDP_xxxx'cr'
TDP_xxxx'cr''lf']
MC TDP_'cr'
TDP_xxxx'cr''lf']
Where: xxxx = NRM (normal data phasing), INV (inverted
data phasing).
Receive Data Phase
Command:
Response:
Status:
Response:
MC RDP_xxxx'cr'
RDP_xxxx'cr''lf']
MC RDP_'cr'
RDP_xxxx'cr''lf']
Where: xxxx = NRM (normal data phasing), INV (inverted
data phasing).
CTS Delay Time
Command:
Response:
Status:
Response:
MC CTSD_xx'cr'
CTSD_xx'cr''lf']
MC CTSD_'cr'
CTSD_xx'cr''lf']
Where: xx = 0 to 60 (number of seconds).
A.3.3 System Commands/Responses
Time of Day
Command:
Response:
Status:
Response:
MC TIME_hh:mmxx'cr'
TIME_hh:mmxx'cr''lf']
MC TIME_'cr'
TIME_hh:mmxx'cr''lf']
Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Date Command:
Response:
Status:
Response:
MC DATE_mm/dd/yy'cr'
DATE_mm/dd/yy'cr''lf']
MC DATE_'cr'
DATE_mm/dd/yy'cr''lf']
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2-digit year mode, and 1975 to 1999
and 2000 to 2075 in 4-digit mode.
Remote Operation
Command:
Response:
MC REM_'cr'
REM_'cr''lf']
The modem will respond to any status request at any time.
However, the modem must be in Remote mode to change
configuration parameters.
Clear Stored Faults
Command:
Response:
MC CLSF_'cr'
CLSF_'cr''lf']
This command is used to clear all stored faults logged by the
modem.
Modem Operation Mode
Command:
Response:
Status:
Response:
MC MOM_xxxxxxx'cr'
MOM_xxxxxxx'cr''lf']
MC MOM_'cr'
MOM_xxxxxxx'cr''lf']
See Warning in Section 9.0.
Where: xxxxxxx = TX_only, RX_only, or Duplex.
This command configures the modem for simplex or duplex
operation modes. When transmit only mode is selected, receive
faults are inhibited. When receive only mode is selected,
transmit faults are inhibited.
Local Modem AUPC
Mode
Command:
Response:
Status:
Response:
MC LMA_xxx’cr’
LMA_xxx’cr’’lf’]
MC LMA_’cr’
LMA_xxx’cr’’lf’]
Where xxx = ON or OFF.
This command configures the modem for the LOCAL
MODEM AUPC mode. When “ON” is selected, the AUPC
configuration can be entered.
A–11