Comtech EF Data SNM-1010L - Manual (Page 204)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
A.3.1 Demodulator Commands/Responses
Set Demodulator
Frequency Command:
Response:
Status:
Response: MC DF_nnn.nnnn'cr'
DF_nnn.nnnn'cr''lf']
MC DF_'cr'
DF_nn.nnnn'cr''lf']
Where: nnn.nnnn = Frequency in MHz, 950.0000 to 1750.0000, in
100 Hz steps for non-terminal frequency display. For terminal
frequency mode, the range will be determined by the LO frequency
and high/low Mix of the ODU.
Demodulator Rate
Preset Assignment Command:
Response:
Status:
Response: MC ADRx_nnnn_mmm.mmm'cr'
ADRx_nnnn_mmm.mmm'cr''lf']
MC ADRx_'cr'
ADRx_nnnn_mmm.mmm'cr''lf']
See Warning in Section 9.0. Where:
x = A, B, C, D, or V (Preset designator).
nnnn = 1/2 (QPSK 1/2), [coder rate], 3/4 (QPSK 3/4), 7/8 (QPSK
7/8), BP12 (BPSK 1/2), 8P23 (8PSK 2/3), OQ12 (OQPSK 1/2),
OQ34 (OQPSK 3/4), OQ78 (OQPSK 7/8), OQSK (OQPSK 1/1),
BPSK (BPSK 1/1) (QPSK (QPSK 1/1),
2144 (BPSK 21/44), B516 (BPSK 5/16), 8P34 (8PSK 3/4).
mmm.mmm = Data rate in kHz.
Demodulator Rate
Preset Selection Command:
Response:
Status: MC SDRx_'cr'
SDRx_'cr''lf']
(See DR command.)
See Warning in Section 9.0.
Where: x = A, B, C, D, or V (Preset designator).
Demodulator Rate
Variable Assignment
and Selection Command:
Response:
Status: MC SDRV_nnnn_mmm.mmm'cr'
SDRV_nnnn_mmm.mmm'cr''lf']
(See DR command.)
See Warning in Section 9.0. Where:
nnnn = 1/2 (QPSK 1/2), [coder rate], 3/4 (QPSK 3/4), 7/8 (QPSK
7/8), BP12 (BPSK 1/2), 8P23 (8PSK 2/3), OQ12 (OQPSK 1/2),
OQ34 (OQPSK 3/4), OQ78 (OQPSK 7/8), OQSK (OQPSK 1/1),
BPSK (BPSK 1/1) (QPSK (QPSK 1/1),
2144 (BPSK 21/44), B516 (BPSK 5/16), 8P34 (8PSK 3/4).
mmm.mmm = Data rate in kHz.
Descrambler Enable Command:
Response:
Status:
Response: MC DE_xxx'cr'
DE_xxx'cr''lf']
MC DE_'cr'
DE_xxx'cr''lf']
Where: xxx = ON or OFF.
Differential Decoder
Enable Command:
Response:
Status:
Response: MC DDEC_xxx'cr'
DDEC_xxx'cr''lf']
MC DDEC_'cr'
DDEC_xxx'cr''lf']
Where: xxx = ON or OFF.
RF Loopback Command:
Response:
Status:
Response: MC RFL_xxx'cr'
RFL_xxx'cr''lf']
MC RFL_'cr'
RFL_xxx'cr''lf']
Where: xxx = ON or OFF.
IF Loopback Command:
Response:
Status:
Response: MC IFL_xxx'cr'
IFL_xxx'cr''lf']
MC IFL_'cr'
IFL_xxx'cr''lf']
Where: xxx = ON or OFF.
A–6