Comtech EF Data SNM-1010L - Manual (Page 221)

SNM-1010L Data/Control Modem Revision 0
Remote Control Channel Commands/Responses MN/SNM1010L.OM
Modulator Rate
Status Status:
Response:
MC MR_'cr'
MR_nnnn_mmmm.mmm'cr''lf']
Where:.
nnnn = 1/2 (QPSK 1/2), [coder rate], 3/4 (QPSK 3/4),
7/8 (QPSK 7/8), BP12 (BPSK 1/2), 8P23 (8PSK 2/3),
OQ12 (OQPSK 1/2), OQ34 (OQPSK 3/4), OQ78
(OQPSK 7/8), OQPSK (OQPSK 1/1), BPSK (BPSK
1/1), QPSK (QPSK 1/1) 2144 (BPSK 21/44), B516
)BPSK 5/16),
8P34 (8PSK 3/4)
mmmm.mmm = Data rate in kHz
Demodulator Rate
Status Status:
Response:
MC DR_'cr'
DR_nnnn_mmmm.mmm'cr''lf']
Where:
nnnn = 1/2 (QPSK 1/2), [coder rate], 3/4 (QPSK 3/4),
7/8 (QPSK 7/8), BP12 (BPSK 1/2), 8P23 (8PSK 2/3),
(OQ12 (OQPSK 1/2), OQ34 (OQPSK 3/4), OQ78
(OQPSK 7/8), OQPSK (OQPSK 1/1), BPSK (BPSK
1/1), QPSK (QPSK 1/1) 2144 (BPSK 21/44), B516
)BPSK 5/16),
8P34 (8PSK 3/4)
mmmm.mmm = Data rate in kHz.
Receive Signal Level
Status Status:
Response:
MC RSL_'cr'
RSL_xsnn.ndBm'cr''lf']
Where:
x = < or > (data modifier to indicate that the receive signal
level is less than or greater than the returned value).
s = + or - (receive signal level sign, plus or minus).
nn.n = 0.0 to 99.9 (receive signal level magnitude).
Notes:
1. The 'x' (< or >) parameter is only returned if the level
has exceeded the computational resolution of the
system.
2. 'No Data' is returned if the level cannot be calculated.
3. Sampling' is returned if not enough data is currently
available to calculate the level.
Interface Buffer Fill
Status Status:
Response: MC IBFS_'cr'
IBFS_nn%'cr''lf']
Where: nn = 1 to 99 (relative to buffer depth).
LNB Current Monitor
Status Status:
Response:
MC LNBC_'cr'
LNBC_nnn'cr''lf']
Where: nnn = 0 to 500 (in 1 mA steps)
Notes:
The 'x' (< or >) parameter is only returned if the level has
exceeded the computational resolution of the system.
'No Data' is returned if the level cannot be calculated.
Sampling' is returned if not enough data is currently
available to calculate the level.
ODU Current Monitor
Status
Status:
Response:
MC ODUC_'cr'
ODUC_nnnn'cr''lf']
Where: nnn = 0 to 4000 (in 1 mA steps)
Notes:
1. The 'x' (< or >) parameter is only returned if the level
has exceeded the computational resolution of the
system.
2. 'No Data' is returned if the level cannot be calculated.
3. Sampling' is returned if not enough data is currently
available to calculate the level.
A–23