Welch Allyn 6000 Series Connex Vital Signs Monitor - User Manual User Manual

Welch allyn connex, Vital signs monitor 6000 series

Table of contents

Document Outline

Contents
Introduction
- Indications for use
- Contraindications
Symbols
- Documentation symbols
- Power symbols
- Connectivity symbols
- Miscellaneous symbols
Screen elements
About warnings and cautions
- General warnings and cautions
Physical design
- Controls, indicators, and connectors
Setup
- Supplies and accessories
- Insert the battery
- Mount the monitor
- Attach the probe well
- Attach the temperature probe
- Remove the temperature probe and well
- Connect the NIBP hose
- Disconnect the NIBP hose
- Connect the SpO2 cable or the SpO2/RRa dual cable
- Disconnect the SpO2 cable or the SpO2/RRa dual cable
- Connect the patient movement cable
- Disconnect the patient movement sensor and cable
- Attach a USB accessory
- Detach a USB accessory
- Insert a new roll of paper
- Connect AC power
- Disconnect AC power
Startup
- Power
  - Power on/Display power-saving button
- Power up the monitor
- Power down the monitor
- Reset the monitor
- Set the date and time
- Enter clinician information
- Set the default configuration
Navigation
- Home tab
- Device Status area
  - Battery status
  - Alarm and information messages
- Content area
- Navigation area
  - Display lock
    - Lock the display
    - Unlock the display
Using the keypad, keyboard, and barcode scanner
- Open the numeric keypad
- Numeric keypad
- Enter a number
- Close the numeric keypad
- Open the keyboard
- Keyboard
- Enter a letter or number
- Enter a symbol or special character
- Enter a diacritical mark
- Close the keyboard
- Use a barcode scanner
Connex CS
- Overview
- Monitor tab
- Connect to the central station
- Disconnect from the central station
- Continuous patient monitoring
- Activate the Continuous Monitoring profile
- Pause continuous monitoring (Pause mode)
- Resume continuous monitoring
- End continuous monitoring
- Assign a patient and location
Profiles
- Continuous Monitoring profile
- Continuous Monitoring profile
- Saving vital sign measurements (Continuous Monitoring profile)
- Intervals Monitoring profile
- Spot Check profile
- Triage profile
- Profile feature comparison
- Profile feature comparison
- Changing profiles
Patient data management
- Add a patient to the patient list
- Load patient data with a barcode scanner
- Select a patient
- Manage patient records (Continuous Monitoring profile)
- Manage patient records (Intervals Monitoring, Spot Check, and Triage profiles)
- Printer
- Delete a patient from the list
Alarms
- Alarm types
- Icons on the Home tab
- Patient rest mode
- Reset (pause or turn off) audio alarms
- Cancel a paused alarm
- Adjust vital sign alarm limits
- Modify audio alarm notification
- Alarm messages and priorities
- Nurse call
Patient monitoring
- Standard and custom modifiers
  - Enter modifiers
- Custom scoring
- Manual overrides
  - Enter a manual override measurement
- Patient movement
  - Movement frame
- Capnography (CO2)
  - etCO2 frame
- Respiration rate
  - RR frame
    - Set up RR
    - Configure RR alarms
- IPI
  - IPI frame
- Acoustic respiration rate (RRa)
- NIBP
- Temperature
- SpO2
- SpHb
- Pulse rate frame
- Manual parameters frame
  - Enter manual parameters
Maintenance and service
- Perform periodic checks
- Replace the printer paper
- Change the battery
- Clean the monitor
  - 70 percent isopropyl alcohol
  - 10 percent chlorine bleach solution
- Clean the accessories
- Clean the stand
Advanced settings
- General
- Parameters
- Data management
- Network
- Service
Troubleshooting
- Patient movement messages
- CO2 messages
- RRa messages
- NIBP messages
- SpO2 and SpHb messages
- Temperature messages
- Weight scale messages
- Patient data management messages
- Communications module messages
- Radio messages
- Ethernet messages
- USB and USB flash drive messages
- System messages
- Battery power manager messages
- Configuration Manager messages
- Printer messages
- Network messages
- Problems and solutions
Specifications
- Physical specifications
- Physical specifications
- Environmental specifications
- Monitor radio
- Configuration options
Standards and compliance
- General compliance and standards
- General radio compliance
Guidance and manufacturer's declaration
- EMC compliance
- Emissions and immunity information
Appendix
- Approved accessories
- Warranty