HP 8360 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for 8360 HP
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 508 |
| Size: | 5.90 MB |
Show table of contents
Document Outline
- Title Page
- Notice
- Restricted Rights Legend
- Certification
- Warranty
- Assistance
- Safety Notes
- General Safety Considerations
- Instruments Covered By This Manual
- User's Handbook Organization
- HP 8360 Series Documentation
- Typeface Conventions
- Regulatory Information
- Manufacturer's Declaration
- Notice for Germany: Noise Declaration
- Declaration of Conformity
- Instrument Markings
- Hewlett-Packard Sales and Service Offices
- PREFACE
- Table of Contents
- 1: GETTING STARTED
- What is in This Chapter
- How To Use This Chapter
- Introducing the HP 8360 Series Synthesized Sweepers
- Display Area
- Entry Area
- CW Operation and Start/Stop Frequency Sweep
- Center Frequency/Span Operation
- Power Level and Sweep Time Operation
- Continuous, Single, and Manual Sweep Operation
- Marker Operation
- Saving and Recalling an Instrument State
- Power Sweep and Power Slope Operation
- Getting Started Advanced
- External Leveling the Synthesizer
- Working with Mixers/Reverse Power Effects
- Working with Spectrum Analyzers/Reverse Power Effects
- Optimizing Synthesizer Performance
- ALC Bandwidth Selection
- Using Step Sweep
- Creating and Using a Frequency List
- Using the Security Features
- Changing the Preset Parameters
- Getting Started Programming
- HP-IB General Information
- Getting Started with SCPI
- Definitions of Terms
- Essentials for Beginners
- Details of Commands and Responses
- Programming Typical Measurements
- In This Subsection
- Using the Example Programs
- HP-IB Check, Example Program 1
- Local Lockout Demonstration, Example Program 2
- Setting Up A Typical Sweep, Example Program 3
- Queries, Example Program 4
- Saving and Recalling States, Example Program 5
- Looping and Synchronization, Example Program 6
- Using the *WAI Command, Example Program 7
- Using the User Flatness Correction Commands, Example Program 8
- Programming the Status System
- Programming the Trigger System
- Related Documents
- 2: OPERATING AND PROGRAMMING REFERENCE
- How To Use This Chapter
- A
- Address
- Adrs Menu
- ALC
- ALC System Simplified Block Diagram
- ALC Bandwidth Select Auto
- ALC Bandwidth Select High
- ALC Bandwidth Select Low
- ALC BW Menu
- Altrnate Regs
- AM BW Cal Always
- AM BW Cal Once
- AM Cal Menu
- AM Menu
- AM On/Off 10 dB/V
- AM On/Off 100%/V
- AM On/Off Ext
- AM On/Off Int
- Ampl Markers
- AM Type 10 dB/V
- AM Type 100%/V
- ANALYZER STATUS REGISTER
- Arrow Keys
- ASSIGN
- Auto Fill Incr
- Auto Fill #Pts
- Auto Fill Start
- Auto Fill Stop
- Auto Track
- B
- C
- CONNECTORS
- D
- E
- F
- G
- H
- I
- Internal AM Depth
- Internal AM Rate
- Internal AM Waveform Noise
- Internal AM Waveform Ramp
- Internal AM Waveform Sine
- Internal AM Waveform Square
- Internal AM Waveform Triangle
- Internal FM Deviation
- Internal FM Rate
- Internal FM Waveform Noise
- Internal FM Waveform Ramp
- Internal FM Waveform Sine
- Internal FM Waveform Square
- Internal FM Waveform Triangle
- Internal Menu
- Internal Pulse Generator Period
- Internal Pulse Generator Rate
- Internal Pulse Generator Width
- Internal Pulse Mode Auto
- Internal Pulse Mode Gate
- Internal Pulse Mode Trigger
- Invert Input
- L
- M
- Modulation
- Amplitude Modulation
- FM Modulation
- Pulse Modulation
- P
- Peak RF Always
- Peak RF Once
- POWER LEVEL
- POWER MENU
- Power Offset
- Power Slope
- Power Sweep
- PRESET
- Preset Mode Factory
- Preset Mode User
- Printer Adrs
- PRIOR
- Programming Language Analyzr
- Programming Language CIIL
- Programming Language SCPI
- Pt Trig Menu
- Pulse Delay Normal
- Pulse Delay Trig'd
- Pulse Menu
- Pulse Menu
- Pulse On/Off Extrnl
- Pulse On/Off Intrnl
- Pulse On/Off Scalar
- Pulse Period
- Pulse Rate
- Pulse Rise Time Auto
- Pulse Rise Time Fast
- Pulse Rise Time Slow
- Pulse Width
- Pwr Mtr Range
- R
- S
- SCPI Conformance Information
- SCPI COMMAND SUMMARY
- SCPI STATUS REGISTER STRUCTURE
- Security Menu
- Selftest (Full)
- Set Atten
- SINGLE
- Software Rev
- SPAN
- START
- Start=M1 Stop=M2
- Start Sweep Trigger Auto
- Start Sweep Trigger Bus
- Start Sweep Trigger Ext
- Step Control Master
- Step Control Slave
- Step Dwell
- Step Points
- Step Size
- Step Swp Menu
- Step Swp Pt Trig Auto
- Step Swp Pt Trig Bus
- Step Swp Pt Trig Ext
- STOP
- SWEEP MENU
- Sweep Mode List
- Sweep Mode Ramp
- Sweep Mode Step
- Sweep Span Cal Always
- Swp Span Cal Once
- SWEEP TIME
- SwpTime Auto
- SYSTEM MENU
- T
- U
- Z
- 2a: ERROR MESSAGES
- 2b: Menu Maps
- 2c: Specifications
- 3: INSTALLATION
- 4: OPERATOR'S CHECK and ROUTINE MAINTENANCE
- 5: Instrument History
- Index