Epson ARM.POWERED ARM720T - Manual (Page 221)

Index
ARM DDI 0229B EPSON Index-3
test registers 11-8
Modes, privileged 8-10
Monitor mode 9-4, 9-12, 9-13
Multi-ICE 9-8
O
Operating modes
Abort mode 2-4
changing 2-4
FIQ 2-4
IRQ mode 2-4
Supervisor mode 2-4
System mode 2-4
Undefined mode 2-4
User mode 2-4
Operating state
ARM 2-1
switching 2-1
to ARM 2-1
to THUMB 2-1
THUMB 2-1
P
Page tables 7-5
Permission faults 7-15, 7-20
Pipeline
follower 8-4
Privileged instructions 8-10
Privileged modes 8-10
Processor
state 9-27
Program status registers
control bits 2-8
mode bit values 2-9
reserved bits 2-9
Programming EmbeddedICE-RT
9-7
Programming watchpoints 9-38
PROT bits 9-35
Protocol converter 9-2
Public instructions 9-20
R
Range 9-36, 9-37, 9-38, 9-43, 9-44
RANGE bit 9-36
Read data bus
AHB 6-11
Register
cache test 11-3
control value 9-36
debug status 9-42
fault address 7-16
fault status 7-16
MMU test 11-8
test 11-1
test state 11-3
translation table base 7-4
Registers 3-3
ARM 2-4
interrupt modes 2-5
Cache Operations Register 3-7
Control Register 3-4
debug communications chan-
nel 9-14
debug control
DBGACK 9-40
DBGRQ 9-40
Domain Access Control Regis-
ter 3-6
Fault Address Register 3-7
Fault Status Register 3-6
ID Register 3-3
instruction 9-20, 9-21, 9-22,
9-23
Invalidate TLB 3-7
Invalidate TLB Single Entry
3-7
Process Identifier Registers
3-8
register 13, process identifier
register
changing FCSE PID 3-8
FCSE PID 3-8
relationship between ARM
and Thumb 2-7
Test Registers 3-9
Thumb 2-6
TLB Operations Register 3-7
Translation Table Base Regis-
ter 3-5, 7-4
watchpoint 9-33
programming and reading
9-33
Registers, debug
address mask 9-37
BYPASS 9-21
bypass 9-22
control mask 9-33, 9-35
control value 9-33, 9-35
data mask 9-33
data value 9-33
EmbeddedICE-RT 9-24
accessing 9-17, 9-24
debug status 9-26
ID 9-22
instruction 9-20, 9-21, 9-22,
9-23
scan path select 9-22, 9-23
scan path select register 9-20
status 9-41
status register 9-26
test data 9-22
watchpoint address mask 9-33
watchpoint address value 9-33
Reset
action of processor on 2-16
Response encoding 6-10
RESTART
on exit from debug 9-21
RESTART instruction 9-21, 9-28,
9-29
Return address calculation 9-32
Returned TCK,
See RTCK
RTCK 9-8
RUN-TEST/IDLE state 9-21, 9-29
S
Scan
input cells 9-20
output cells 9-20
path 9-20
paths 9-17
Scan cells 9-21, 9-24
Scan chain
selected 9-20
Scan chain 1 9-17, 9-24, 9-25, 9-27,
9-28, 9-29, 9-30
Scan chain 1 cells 9-25
Scan chain 2 9-17, 9-24, 9-33
Scan chains 9-17
number allocation 9-23
Scan path select register 9-20,
9-22, 9-23
SCAN_N 9-20, 9-23, 9-24
Section
descriptor 7-8
references, translating 7-10
SHIFT-DR 9-19, 9-20, 9-21, 9-25
SHIFT-IR 9-23
Signals
AMBA interface A-1
coprocessor interface A-2
debugger A-4
ETM interface A-5
JTAG A-3
miscellaneous A-7
Single-step core operation 9-20
SIZE 6-7
SIZE bits 9-35
Slave
transfer response 6-9
Small page references, translating
7-13
Software breakpoints 9-36, 9-37
clearing 9-37
programming 9-37
setting 9-37
Software Interrupt 2-13
Software interrupt 2-13
SPSR (Saved Processor Status
Register) 2-8
format of 2-8
State
CAPTURE-DR 9-20, 9-21
processor 9-27
SHIFT-DR 9-19, 9-20, 9-21,
9-22
UPDATE-DR 9-20, 9-21
UPDATE-IR 9-23
Subpages 7-14
Supervisor mode 2-4