Orion System VCC-X Controller - Manual (Page 89)

VCC-X Operator Interface SD
INDEX
89
E-M
E
Economizer
Maximum Position if High CO
2
Level
Setpoint.........48
Overrides.........81
Economizer %.........59
Economizer Active Relay Description........38
Economizer Control Loop Rate.........30
Economizer Control Type.........30
Economizer Enabled.........59
Economizer Enable Setpoint.........47
Economizer Enable Source Screen.........30
Economizer in IAQ Mode.........59
Economizer in Unoccupied Mode.........30
Economizer Minimum Damper
Position.........47
Economizer Minimum Position.........59
Economizer Voltage Output.........31
EM1 Installed.........26
EM1 Relay Confi guration Screens.........37
EM1 Relays.........62
Emergency Shutdown.........35
Energy Saving Timer.........12
Enter
Key.........10,16
New Passcode.........19
ESC Key Defi ned.........10,16
Return Air Relative Humidity
Percentage.........57
Exhaust Air CFM.........60
Exhaust Airfl ow Duct Size.........34
Exhaust Airfl ow Monitoring.........34
Exhaust Fan Output Screen.........32
Exhaust Fan Relay Description.........38
Exhaust Fan Status.........60
Exhaust Fan VFD.........48
Exhaust VFD Override.........82
Expansion Relays Heating Stages
VAV/Zone.........70
Expansion Valve 1 Position.........68
Expansion Valve 2 Position.........68
F
Fahrenheit.........25
Fan Cycle Mode Screen.........28
Fan On Min.........74
Fan Proving Screen.........28
Fan Starting Delay Screen.........29
Fan Status.........77
Fan VFD Signal.........27
Fan Voltage Output Screen.........28
Fixed Damper Force Mode.........78
Fixed Position Damper Airfl ow.........74
H
H/C Changeover Box VAV/Zone.........69
Head Pressure Setpoint.........68
Head Pressure Setpoints - Cooling and
Reheat.........47
Heat/Cool Changeover Delay.........36
Heating
Min Off Time.........36
Min Run Time.........36
Setpoints.........76
Stage Down.........36
Stage Up.........36
Heating Active Stages Status.........57
Heating/Cooling Demand
VAV/Zone Status.........76
Heating Enabled Status.........56
Heating Outputs.........57
Heating Setpoints Status.........55
Heating Stage Relay Description.........38
Heating Unoccupied Offsets.........41
Heat Reset Source Setpoints - High/
Low Reset.........45
Heat Total
MiniLink PD Status.........80
Heat Type Screen.........29
Heat Wheel Defrost Temperature
Setpoint.........50
Heat Wheel Relay Description.........38
High Head Pressure Alarm.........68
Hi SAT Cutoff.........49
Holidays
Programming.........14
Start/Stop Times.........15,23
Hood On HVAC Setpoints.........40
Humidity Control Sensor Type.........32
HVAC Cool/Heat Setpoints.........40
HVAC Hood On Setpoints.........40
HVAC Mode
Cooling Setpoints.........40,41
Heating Setpoints.........40,41
Unoccupied Offsets.........41
HVAC Mode Deadband.........41
HVAC Mode Set By Remote Contact.........27
HVAC Mode Status.........55
HVAC Source Screen.........26
I
IAQ Economizer.........30
Indoor Relative Humidity Setpoint
Percentage.........57
Indoor RH.........57
Indoor RH Setpoint.........43
Initialization Screen.........11,17
K
Keys Described.........10,16
L
Last Polled Zone MiniLink PD.........79
Leaving Air Temperature Setpoint.........57
Level 1 & Users Defi ned.........19
Loop Search.........20
Low Ambient Relay Description.........38
Low Ambient Setpoint.........50
Low Suction Pressure Alarm.........68
Low Superheat 1 Alarm.........68
Low Superheat 2 Alarm.........68
M
Main Fan Status VAV/Zone.........70
Maverick Testing MiniLink PD.........80
Max Adjust Static Pressure Control
Rate.........28
Maximum
Damper Force Mode.........78
EMS Offset VAV/Zone.........75
Slide Offset VAV/Zone.........75
Maximum Economizer Position in Heat
Mode.........47
Maximum Outdoor Air CFM.........47
Mechanical Heat/Cool Alarm Delay.........30
MHGRV-X Enabled Status.........57
MHGRV-X Installed.........26
MHGRV-X Reheat Valve Output Signal
Percentage Status.........57
Min Damper Force Mode.........78
MiniLink PD Confi guration.........79
Alarm Polling.........80
Last Polled Zone.........79
Maverick Testing.........80
Mode Changeover Time.........79
Optimal Start Target Zone.........80
System Type.........79
MiniLink PD Status
Adding Additional.........20
Cool Total.........80
Heat Total.........80
Minutes Left.........80
Mode Priority.........80
Schedule Mode.........80
System Status.........80
Minimum Outdoor Air CFM.........47
Minimum Outdoor Airfl ow.........47
Minimum Run Times and Off Times.........36
Minus Key Defi ned.........10,16
Minutes Left, MiniLink PD Status.........80
Mod
Cooling Override.........82
Heating Override.........81