Orion System OE338-23-XX User Manual
Description, Mounting, Page

Form: ORION-OE338-23-GPCXP-Controller-01B.doc
Page
1 of 1
Description
The OE338-23-GPCXP GPC-XP Controller is
used for controlling equipment or processes
that cannot be controlled using a standard
HVAC controller.
The GPC-XP provides the flexibility to con-
trol, schedule and/or monitor equipment such
as unit heaters, exhaust fans, motorized
dampers, pumps, and other mechanical
equipment. It can also be used for simple
boiler, chiller, or refrigeration applications as
well as to provide lead/lag start function.
The GPC-XP has an on-board CommLink
that provides for stand-alone programming
and monitoring via a direct USB connection
to a computer running Prism II software. If
used on a networked system that has an ex-
ternal CommLink, this on-board CommLink
would not be used.
The GPC-XP has (8) configurable analog
inputs which will accept signals from thermis-
tor temperature sensors or from 4-20mA, 0-
5VDC, or 0-10VDC transmitters. The inputs
are set for the desired scaling by means of a
jumper bar. Custom formulas created by
available math functions and operators can
be used in conjunction with the analog inputs
to create a calculated value to be used and displayed for a specific analog input. An additional modular input is available for
WattMaster communicating sensors. The GPC-XP has (8) wet contact binary inputs that can be configured for either normally
open or normally closed operation. Also available are (8) relay outputs for on/off control and (4) analog outputs (0-10VDC) for
modulating control. Highest/lowest/average of the analog input values can be used in the GPC-XP logic or broadcast to other
controllers on the control system loop. There are (8) separate two events per day schedules which can be assigned to any
input or output for operational control or for alarm recognition based on time of day. These schedules can also be configured
to broadcast to other WattMaster
controllers on the control system loop.
Mounting
The GPC-XP is provided with an integral plastic enclosure which provides mounting points for mounting inside of a
control enclosure. It is recommended that the GPC-XP be mounted in a control enclosure in the building equipment
room. An optional factory control enclosure for the GPC-XP is also available.
OE338-23-GPC-XP
GPC-XP Controller
7.83
7.83
8.38
8.38
0.29
0.29
2.75
2.75
5.98
5.98
4.10
4.10
0.70
0.70
1.49
0.98
0.98
CO
M
F
RO
M
G
N
D
CU
T
T
O
IS
O
L
A
TE
WATTMASTER CONTROLS
YS102432 REV 3
LOOP COMM
GND
+24V
+5V
OUTPUTS
ADDRESS
ADD
1
2
4
8
16
32
POWER
EBUS
STATUS2
STATUS1
OUTPUTS
ANALOG
SERIAL #
OUTPUTS
RELAY
SH
R+
T-
BIN8
BIN7
BIN6
BIN5
BIN4
BIN3
BIN2
BIN1
BINARY
INPUTS
INPUTS
ANALOG
0-
5v
0-
10v
4-
20
mA
AO
U
T
1
-2
C14
R109
TB8
U19
U17
TB7
TB6
TB4
TB3
TB2
TB1
SW1
R97
R74
R6
1
R5
9
R5
5
R5
1
R4
7
R4
3
R4
1
R3
8
R21
R16
R14
D13
D12
D10
D9
D8
D7
D6
C46
C36
C21
RLY1
RLY2
RLY3
RLY4
COMMON
MADE IN USA
RLY1
RLY2
RLY3
RLY4
COMMON
AOUT1
AOUT2
AOUT3
AOUT4
GND
GND
1002
1002
.1uF
.1uF
A
OU
T
3
-4
GND
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
.1uF
.01uF
LOOP
B
A
UD
1
2
AI7
AI8
AI6
AI5
AI4
AI1
AI2
AI3
GND
GND
GND
GND
AI8
AI7
AI6
AI5
AI4
AI3
AI2
AI1
TH
E
R
M
VDC
300
300
300
300
300
300
300
300
COM
COM
COM
COM
D11
CONNEC
ON BOA
COMMLI
Technical Data
OE338-23-GPCXP GPC-XP Controller
Power
24 Volt AC
Weight
1 lb.
Power Consumption
8 VA Maximum
Network Connection
RS-485 – 9600 or 57,600 Baud
Operating Temp
-30
F to 150F
Protocol
HSI Open Protocol Token Passing
Operating Humidity
90% RH Non-Condensing
Communications
E-BUS
Inputs:
Outputs:
Types of Allowed
Inputs
Type III-10K Ohm Sensors
Total Relay Qty. On Board 8
4-20mA
Relay Power Rating
(2 Amp @ 24 VAC)
0-5VDC & 0-10VDC
Analog Output Qty.
4
N.O. or N.C. Contact
Analog Output Signal
0-10 VDC
Total Inputs Available
16 Configurable
Lead Lag Scheduling
(1) Output can be Configured
Additional
Communicating
Sensor Input
1 (Modular)
Schedules Available
(8) 2 Events per day
Three Year Warranty
WattMaster reserves the right to
change specifications without notice