Leica Geosystems Leica mojo3D - User Manual User Manual

Leica user manual mo j o3d

Table of contents

Document Outline

Introduction
Table of Contents
1 System Overview
- 1.1 General mojo3D System Information
- 1.2 Components of the mojo3D System
- 1.3 Features and Specifications
2 System Installation
- 2.1 Before Installation
- 2.2 mojo3D Installation
- 2.3 Antenna Installation
- 2.4 SIM Card Installation
3 Running the mojo3D for the First Time
- 3.1 Starting Up
- 3.2 Setting the Screen Calibration
- 3.3 Initial Setup Wizard
- 3.4 Menu Buttons at Right of Screen
- 3.5 Menu Buttons at Left of Screen
- 3.6 Specifying Data for Display
- 3.7 Zoom Buttons
- 3.8 View Modes
- 3.9 Error Notifications
- 3.10 Running the Setup Wizard at any Time
- 3.11 Changing System Settings
- 3.12 Vehicle Setup
- 3.13 Attached Device Selection
- 3.14 NMEA Configuration
- 3.15 Feature Unlock
4 Setting Guidance Types
- 4.1 AB Parallel Guidance
- 4.2 A+ Heading Guidance
- 4.3 Fixed Contour Guidance
- 4.4 Pivot Guidance
- 4.5 Ultimate Curve Guidance
- 4.6 Stop Guidance
- 4.7 Guidance Management
- 4.8 Field Offset
- 4.9 Nudge
5 Auto-Steer
- 5.1 Engage Auto-Steer
- 5.2 Tuning Auto-Steer Performance
- 5.3 Stationary Engage and Reverse Steering
- 5.4 Testing Auto-Steer
6 Treatments
- 6.1 Starting a New Treatment
- 6.2 Load a Stored Treatment
- 6.3 Changing a Treatment Name
- 6.4 Creating a PDF Report of a Treatment
- 6.5 Deleting a Treatment
- 6.6 Exporting Treatment Data
- 6.7 Importing Treatment Data
7 Automatic Section Control
- 7.1 Section Control Latency
  - 7.1.1 Calibrating the Section Control Latency Value
  - 7.1.2 Troubleshooting Latency Problems
- 7.2 Setting the Overlap Limit
- 7.3 Setting the Low-Speed Shutoff
- 7.4 Section Override Control
8 Field Boundary
- 8.1 Create a New Field Boundary
- 8.2 Load a Stored Field Boundary
- 8.3 Changing a Field Boundary Name
- 8.4 Deleting a Field Boundary
- 8.5 Exporting Field Boundary Data
- 8.6 Importing Field Boundary Data
9 Vehicles and Implements
- 9.1 Saving a Vehicle or Implement Configuration
- 9.2 Load a Vehicle or Implement Configuration
- 9.3 Renaming a Vehicle or Implement Configuration
- 9.4 Deleting Vehicle or Implement Configurations
- 9.5 Exporting Vehicle or Implement Configurations
- 9.6 Importing Vehicle and Implement Configurations
10 Correction Sources
- 10.1 Network DGPS
- 10.2 SBAS
- 10.3 GL1DETM
- 10.4 Network RTK
- 10.5 RTK Base Station (Internal Radio)
11 NMEA Output
- 11.1 Configuring NMEA Output
- 11.2 Logging NMEA Data to USB
- 11.3 NMEA Sentences Available
12 Virtual Wrench™ Remote Service
- 12.1 Virtual Wrench™
- 12.2 Making a Service Request
- 12.3 Upgrading Software from Virtual Wrench™
- 12.4 Upgrading Software via USB Flash Drive
- 12.5 Restoring Previous Software Version
- 12.6 Backing Up Current Software
- 12.7 Serial Numbers and Other System Information
13 Care and Transport
- 13.1 Transport
- 13.2 Storage
- 13.3 Cleaning and Drying
14 Safety Directions
- 14.1 General Introduction
- 14.2 Intended Use
- 14.3 Limits of Use
- 14.4 Responsibilities
- 14.5 Hazards of Use
- 14.6 Electromagnetic Compatibility (EMC)
- 14.7 FCC Statement, Applicable in U.S.
- 14.8 ICES-003 Statement, Applicable in Canada
- 14.9 Labelling
15 Technical Data
- 15.1 mojo3D Display Technical Data
- 15.2 mojo3D GPS Receiver Technical Data
- 15.3 Wireless Modules Technical Data
  - 15.3.1 HSDPA Wireless Module Technical Data
  - 15.3.2 CDMA Wireless Module Technical Data
- 15.4 Antennas Technical Data
- 15.5 mojoXact Technical Data
- 15.6 mojoXact GPS Receiver Technical Data
- 15.7 mojoXact Plus Technical Data
- 15.8 mojoXact Plus GPS Receiver Technical Data
- 15.9 Conformity to National Regulations
16 International Limited Warranty, Software License Agreement
Appendix A mojo3D Enhancements
- A.1 mojo3D with Single Section Control
- A.2 mojo3D with Multi Section Control Kit
- A.3 mojo3D with GeoPRO Antenna
- A.4 mojo3D with mojoXact Kit
- A.5 Redeeming a System Option Voucher
Appendix B Formatting USB Flash Drives
Appendix C GNU General Public License
Appendix D Glossary of Terms