KYORITSU 6300 Instruction Manual - Manual (Page 31)

4. 5
MODEL6300
Section 4 Setting MODEL6300
4-3-1 “Setting 01” Wiring
Setting item
1P2W(1ch) : Single-phase 2-wire (1ch)
1P2W(2ch) : Single-phase 2-wire (2ch)
1P2W(3ch) : Single-phase 2-wire (3ch)
1P3W : Single-phase 3-wire
3P3W : Three-phase 3-wire
3P4W : Three-phase 4-wire
Default value 3P3W
* Using the Cursor key whilst in the selection screen, select “Setting 01”.
* Press the ENTER key to enter setting change mode.
* Previous setting (or default value: 3P3W) flickers. Select the desired wiring
configuration with the
Cursor key, and then press the ENTER key.
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ • • ⁈ • • ⁈ ‣ ⁂․ ⁉ ․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁉ ‥ ⁂ ‥ ⁂‥ ⁉ ‥ ⁂… ⁉ … ⁉
‧″ ‧″ ‣ •″ ․ •″ •″ ‧• ″ ‣ •• ″ ․ • •″ ‧• •″ •″ ‣ •• •″
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ ‣ ⁂․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁂‥ ⁉ ‥ ⁂… ⁉
‧″ ‧″ ‣ •″ ․ •″ ‧• ″ ‣ •• ″ ․ • •″ ‧• •″ ‣ •• •″ •″
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ ‣ ⁂․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁂‥ ⁉ ‥ ⁂… ⁉
‧″ ‣ •″ ․ •″ ‧• ″ ‣ •• ″ ․ • •″ ‧• •″ ‣ •• •″ •″
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ • • ⁈ • • ⁈ ‣ ⁂ ‣ ⁂․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁉ ‥ ⁂‥ ⁉ ‥ ⁉ ‥ ⁂ ‥ ⁂… ⁉ … ⁉
‧″ ‣ •″ ․ •″ •″ ‧• ‧• ″ ‣ •• •• ″ ․ • •″ •″ ‧• ‧• •″ ‣ •• •″
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ ‣ ⁂․ ⁉ ․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁂ ‥ ⁂‥ ⁉ ‥ ⁂… ⁉
‧″ ‧″ ‣ •″ •″ ․ •″ •″ ‧• ‧• ″ ‣ •• ″ ․ • •″ •″ ‧• •″ ‣ •• •″
‣ ‧• ⁈ ‥• • ⁈ • • ⁈ • • ⁈ ‣ ⁂ ‣ ⁂․ ⁉ ․ ⁉ ‣⁂ ‥ ⁉ ‥ ⁉ ‥ ⁂ ‥ ⁂‥ ⁉ ‥ ⁂… ⁉ … ⁉
‧″ ‣ •″ ․ •″ ‧• ″ ‣ •• ″ ․ • •″ ‧• •″ ‣ •• •• •″
1P2W(1ch)
1P2W(2ch) 1P2W(3ch) 1P3W
3P3W 3P4W
or
or
‣ ‧• ⁈ ‥ ••⁈ • •⁈ ‣⁂ ․⁉ ‣⁂ ‥⁉ ‥ ⁂‥ ⁉ ‥ ⁂…⁉
‧″ ‣ •″ ․• ″ ‧ •″ ‣ ••″ ․ ••″ ‧• •″ ‣•• •″