Burkert Type 8793 User Manual
Burkert Sensors
This manual is related to the following products:
Table of contents
Document Outline
- Table of contents
- General information and safety instructions
- Description of System
- Installation
- Operation
- Start-Up
- Auxiliary functions
- Operating structure / Factory settings
- PROFIBUS DP
- DeviceNet
- Maintenance and Troubleshooting
- Packaging, Storage, Disposal
- Additional technical information
- Tables for customer-specific settings
- 1. Operating instructions
- 2. Authorized use
- 3. Basic safety instructions
- 5. General information
- 6. Description and features of the Type 8792/8793
- 7. Structure
- 8. Positioner Type 8792
- 9. Process controller Type 8793
- 10. Interfaces of the positioner / process controller
- 11. Technical data
- 12. Attachment and assembly
- 13. Fluid connection
- 14. Electrical connection - Circular plug-in connector version (multi-pole version)
- 15. Electrical connection - Terminal version for cable gland
- 16. Operating levels
- 17. Operating and display elements
- 18. Operating states
- 19. Activating and deactivating auxiliary functions
- 20. Manually opening and closing the valve
- 21. Start-up sequence
- 23. Basic setting of the device
- 24. Activation of the process controller
- 25. Basic setting of the process controller
- 25.1. P.CONTROL – Setting up and parameterization of the process controller
- 25.2. SETUP – Setting up the process controller
- 25.2.1. PV-INPUT – Specifying signal type for the process actual value
- 25.2.2. PV-SCALE – Scaling of the process actual value
- 25.2.3. SP-INPUT – Type of the set-point value default (internal or external)
- 25.2.4. SP-SCALE – Scaling of the process set-point value (for external set-point value default only)
- 25.2.5. P.CO-INIT – Smooth switchover MANUAL-AUTOMATIC
- 25.3. PID.PARAMETER – Parameterizing the process controller
- 25.3.1. Procedure for inputting the parameters
- 25.3.2. DBND – Insensitivity range (dead band)
- 25.3.3. KP – Amplification factor of the process controller
- 25.3.4. TN – Reset time of the process controller
- 25.3.5. TV – Hold-back time of the process controller
- 25.3.6. X0 – Operating point of the process controller
- 25.3.7. FILTER – Filtering of the process actual value input
- 25.4. P.Q‘LIN – Linearization of the process characteristic
- 25.5. P.TUNE – Self-optimization of the process controller
- 26. Configuring the auxiliary functions
- 26.1. Activating and deactivating auxiliary functions
- 26.2. Overview and description of the auxiliary functions
- 26.2.1. CHARACT – Select the transfer characteristic between input signal (position set-point value) and stroke
- 26.2.2. CUTOFF – Sealing function
- 26.2.3. DIR.CMD – Sense of effective direction of the positioner set-point value
- 26.2.4. DIR.ACT – Sense of effective direction of the actuator drive
- 26.2.5. SPLTRNG – Signal split range
- 26.2.6. X.LIMIT – Limits the mechanical stroke range
- 26.2.7. X.TIME – Limiting the control speed
- 26.2.8. X.CONTROL – Parameterization of the positioner
- 26.2.9. P.CONTROL – Setting up and parameterization of the process controller
- 26.2.10. SECURITY – Code protection for the settings
- 26.2.11. SAFEPOS – Input the safety position
- 26.2.12. SIG.ERROR – Configuration of signal level fault detection
- 26.2.13. BINARY.IN – Activation of the binary input
- 26.2.14. OUTPUT – Configuring the outputs (option)
- 26.2.15. CAL.USER – Calibration of actual value and set-point value
- 26.2.16. SET.FACTORY – Resetting to the factory settings
- 26.2.17. SER. I\O – Settings of the serial interface
- 26.2.18. EXTRAS – Setting the display
- 26.2.19. POS.SENSOR – Setting interface remote path sensor
- 26.2.20. SERVICE
- 26.2.21. SIMULATION – Menu for simulation of set-point value, process and process valve
- 26.2.22. DIAGNOSE – Menu for monitoring valves (option)
- 26.3. Manual configuration of X.TUNE
- 27. Operating structure and factory settings
- 28. Description of the PROFIBUS DP
- 29. Electrical connections
- 29.1. Connection diagram Type 8792
- 29.2. Connection diagram Type 8793
- 29.3. X1 - M12, 8-pole circular connector
- 29.4. X2/X3 - M12, 5-pole socket/circular connector - bus connection
- 29.5. X4 - M8, 4-pole socket, optional - Remote Sensor (for remote model only)
- 29.6. X5 - M8, 4-pole circular connector - process actual value (Type 8793 only)
- 29.1. Connection diagram Type 8792
- 30. Start-up PROFIBUS DP
- 31. Description
- 32. Electrical connections
- 32.1. Connection diagram Type 8792
- 32.2. Connection diagram Type 8793
- 32.3. X1 - M12, 8-pole circular connector
- 32.4. X3 - M12, 5-pole circular connector - bus connection
- 32.5. X4 - M8, 4-pole socket, optional - Remote Sensor (for remote model only)
- 32.6. X5 - M8, 4-pole circular connector - process actual value (Type 8793 only)
- 32.7. Terminating circuit for DeviceNet systems
- 32.8. Network topology of a DeviceNet system
- 32.1. Connection diagram Type 8792
- 33. Start-up DeviceNet
- 34. Maintenance
- 36. Packaging and transport
- 39. Selection criteria for continuous valves
- 40. Properties of PID Controllers
- 41. Adjustment rules for PID Controllers
- 42. Table for your settings on the positioner
- 43. Table for your settings on the process controller Type 8793