Extron Electronics DVS 510 Series User Guide - Manual (Page 98)

DVS 510 Series • HTML Configuration and Control 92
• EDID : Select an EDID (resolution and refresh rate) for inputs 5, 6, 8, and 10. You can
select Match Output , which applies the EDID of the output to the selected input, or
select one of the following EDIDs:
640x480 @ 50 Hz 1024x1024 @ 60 Hz 1360x768 @ 75 Hz 1680x1050 @ 60 Hz 1080i @ 60 Hz
640x480 @ 60 Hz 1024x1024 @ 75 Hz 1365x768 @ 50 Hz 1600x1200 @ 50 Hz 1080p @ 23.98 Hz
640x480 @ 75 Hz 1280x768 @ 50 Hz 1365x768 @ 60 Hz 1600x1200 @ 60 Hz 1080p @ 24 Hz
800x600 @ 50 Hz 1280x768 @ 60 Hz 1365x768 @ 75 Hz 1920x1200 @ 50 Hz 1080p @ 25 Hz
800x600 @ 60 Hz 1280x768 @ 75 Hz 1366x768 @ 50 Hz 1920x1200 @ 60 Hz 1080p @ 29.97 Hz
800x600 @ 75 Hz 1280x800 @ 50 Hz 1366x768 @ 60 Hz 480p @ 59.94 Hz 1080p @ 30 Hz
852x480 @ 50 Hz 1280x800 @ 60 Hz 1366x768 @ 75 Hz 480p @ 60 Hz 1080p @ 50 Hz
852x480 @ 60 Hz 1280x800 @ 75 Hz 1365x1024 @ 50 Hz 576p @ 50 Hz 1080p @ 59.94 Hz
852x480 @ 75 Hz 1280x1024 @ 50 Hz 1365x1024 @ 60 Hz 720p @ 25 Hz 1080p @ 60 Hz
1024x768 @ 50 Hz 1280x1024 @ 60 Hz 1365x1024 @ 75 Hz 720p @ 29.97 Hz 2040x1080 @ 23.98 Hz
1024x768 @ 60 Hz* 1280x1024 @ 75 Hz 1440x900 @ 50 Hz 720p @ 30 Hz 2040x1080 @ 24 Hz
1024x768 @ 75 Hz 1360x765 @ 50 Hz 1440x900 @ 60 Hz 720p @ 50 Hz 2040x1080 @ 25 Hz
1024x852 @ 50 Hz 1360x765 @ 60 Hz 1440x900 @ 75 Hz 720p @ 59.94 Hz 2040x1080 @ 29.97 Hz
1024x852 @ 60 Hz 1360x765 @ 75 Hz 1400x1050 @ 50 Hz 720p @ 60 Hz 2040x1080 @ 30 Hz
1024x852 @ 75 Hz 1360x768 @ 50 Hz 1400x1050 @ 60 Hz 1080i @ 50 Hz 2040x1080 @ 50 Hz
1024x1024 @ 50 Hz 1360x768 @ 60 Hz 1680x1050 @ 50 Hz 1080i @ 59.94 Hz 2040x1080 @ 59.94 Hz
*Default 2040x1080 @ 60 Hz
Output Configuration section
In this section, you can select output parameters from the following drop-down menus:
• Resolution : Select the resolution and refresh rate for the current output. Note that
resolutions on this menu are linked to refresh rates as shown in the table above.
• Output Sync Format : Select the output signal type required by the display
device. Available selections are RGBHV (default), RGBS , RGsB , YUV Bi-Level , and
YUV Tri-Level .
• Output Polarity : Select the combination of horizontal and vertical sync signal
polarities. Available selections are H- V- (default), H- V+ , H+ V- , and H+ V+ .
Advanced Configuration section
In this section, you can perform additional configuration by making selections from the
following menus:
• RGB Delay : Select a period of delay before a new image is displayed on the screen,
allowing the display device to adjust to the new sync timing. Options are 0.0 through
5.0 seconds in 0.1-second increments.
• Test Pattern : Select a test pattern to assist you in adjusting the display device for color,
convergence, focus, resolution, contrast, grayscale, and aspect ratio. Figure 44 on the
next page shows the test patterns that are available.