Extron Electronics DVS 510 Series User Guide User Manual
Page 112
DVS 510 Series • HTML Configuration and Control 106
Picture Control (PIP)
In the Picture Control section, adjust the PIP controls as desired. Except for
Pan
, you can
adjust these by either clicking the
+
or
–
button to increase or decrease the value in the text
field, or by keying in a value.
•
Horizontal Shift
: Move the image to the right or left on the display. The value in the
text box is the distance in pixels of the left edge of the image from the left edge of the
display. The range is dependent on the output; the default is
0
plus or minus the output
rate. (This is the same as horizontal positioning or centering.)
•
Vertical Shift
: Move the image up or down on the display. The value in the text box
is the distance in lines of the top edge of the image from the top edge of the display.
The range is dependent on the output; the default is
0
plus or minus the output rate.
(This is the same as vertical positioning or centering.)
•
Horizontal Size
: Stretch or shrink the image horizontally. The value in the text box is
the width of the image in pixels. The range is dependent on the output rate.
•
Vertical Size
: Stretch or shrink the image vertically. The value in the text box is the
height of the image in lines. The range is dependent on the output rate.
•
Color
: Adjust the intensity of the colors in the image. (At the lowest adjustment, all
colors appear as shades of gray.) The range is
000
through
127
; the default is
064
.
•
Tint
: Change the appearance of the colors in the selected window. The range is
000
to
127
; the default is
064
.
•
Brightness
: Set the black level of the input. The range is
000
through
127
; the default
is
064
.
•
Contrast
: Increase or decrease the range of image light and dark values in the image.
The range is
000
through
127
; the default is
064
.
•
Detail Filter
: Adjust the sharpness of the image in the image. The range is
000
through
127
; the default is
064
.
•
Zoom
: Increase or decrease the size of the image while keeping the aspect ratio
constant. The range is dependent on the output rate.
•
Pan
: Click the
L
or
R
button to move the focus on the image left or right. Click the
U
or
D
button to pan up or down. Pan is available only if
Zoom
is set to greater than 100%.
Input Sampling (PIP)
The input sampling controls for the PIP window also can be adjusted by clicking the
+
or
–
button to adjust the value in the text field, or by keying in a value.
•
Horizontal Start: Specify the distance in pixels from the left edge of the total video
display area of the selected input to the left edge of its active area. The default is
128
.
•
Vertical Start: Specify the distance in pixels from the top edge of the total video display
area of the selected input to the top edge of its active area. The default is
128
.
•
Pixel Phase (RGB and YUVp/HDTV inputs only): Adjust the point at which pixels are
sampled for the selected input. The range is
1
through
31
; the default is
16
.
•
Total Pixels (RGB and YUVp/HDTV inputs only): Increase or decrease the width in
pixels of the total line of video. The default is the auto-sensed value. The range is
±512
from the auto-sensed value.
•
Active Pixels: Increase or decrease the width in pixels of the active video area of
the selected input. The default is the auto-sensed value. The range is
±512
from the
auto-sensed value.
•
Active Lines: Increase or decrease the height in lines of the active video area of
the selected input. The default is the auto-sensed value. The range is
±512
from the
auto-sensed value.