Audio, Volume – Extron Electronics DVS 510 Series User Guide User Manual
Page 67
DVS 510 Series • Remote Configuration and Control
61
Command
ASCII Command
(Host to Scaler)
Response
(Scaler to Host)
Additional Description
Picture-in-Picture (PIP) (continued)
View PIP input
E
PIP
}
X! ]
View the input in the PIP window.
Swap
%
Tke
]
Exchange the displayed content between
the main and PIP windows.
Audio Commands
Audio Volume
Set output volume
X5)
V
Vol
X5)
]
Set the volume for the output to
X5).
Increment volume
+
V
Vol
X5)
]
Increase the audio volume.
Decrement volume
–
V
Vol
X5)
]
Decrease the audio volume.
View volume
V
X5)
]
Show the current volume setting.
Audio Gain and Attenuation (per input)
NOTE:
The set gain (G) and set attenuation (g) commands are case sensitive. The increment, decrement, and view
commands are not.
Set audio gain
X5@
G
In
X!
•
Aud
X5$
]
Set audio gain level to
X5@
dB.
Example
5G
In
X!
•
Aud5
]
Set the audio gain to 5 dB.
Set attenuation
X5#
g
In
X!
•
Aud
X5$
]
Set attenuation to
X5#
dB.
Example
15g
In
X!
•
Aud
–15
]
Set the audio attenuation to -15 dB.
Increment level
+
G
In
X!
•
Aud
X5$
]
Increase the audio level by 1 dB.
Decrement level
–
G
In
X!
•
Aud
X5$
]
Decrease the audio level by 1 dB.
View
G
X5$
]
View the current audio level.
Audio Bass (global)
Set the bass level
X5%
<
Bas
X5%
]
Set the global bass level to
X5%
.
Example
10
<
Bas
010
]
Set the bass level to +3 dB.
Increment bass
+
<
Bas
X5%
]
Increase the bass level.
Decrement bass
–
<
Bas
X5%
]
Decrease the bass level.
View bass level
<
X5%
]
Show the current bass level.
Audio Treble (global)
Set the treble level
X5%
>
Trb
X5%
]
Set the global treble level to
X5%
.
Increment treble
+
>
Trb
X5%
]
Increase the treble level.
Decrement treble
–
>
Trb
X5%
]
Decrease the treble level.
View treble level
>
X5%
]
Show the current treble level.
Power Amp Limiter (DVS 510 SA only)
Enable
E
1
APWR
}
Apwr
1
]
Enable the power amp limiter to detect
and eliminate clipping distortion.
Disable
E
0
APWR
}
Apwr
0
]
Disable the power amp limiter.
View setting
E
APWR
}
X1)
]
Show current power amp limiter setting.
NOTE: X!
= PIP input selection
1 through 10
X1)
= Limiter on and off
0 = off, 1 = on
X5)
= Audio volume level
0 through 100
X5@
= Audio gain level
0 through 12 dB (dependent of resolutions)
X5#
= Audio attenuation level
0 through 12 dB (decibels below 0)
X5$
= Audio gain or attenuation (unit response)
-12 dB through +12 dB (can be positive or negative)
X5%
= Audio bass and treble
0 through 16 (-12 dB through +12 dB) in increments of 1.5 dB:
0 = -12 dB, 8 = 0 dB (default), 16 = 12 dB