Visara LINCS Central Control User Manual
Page 64
58
LINCS Central Control
707024-002
Feature Activation/Deactivation
LINCS C8.2 Central Control
The following features are currently enabled:
IPX SNA/TN3270 Clients
016 Extended ESCON CUs
Feature Disk installed: 004 Extended ESCON CUs
PF: 1-Menu
4-Activate 5-Deactivate
Once the PF4 or PF5 option is chosen to activate or deactivate a feature, the panel will be
updated to reflect the currently activated features.
When you are done, or if you chose not to activate or deactivate a feature, you may press PF1
to return to the Customization Data menu.
FAD Options
Below is a list of the FADs which require activation using a Feature Activation Disk. If these
features are configured, but not activated, then an IML error will occur. You must either
reconfigure and disable the feature in error, or activate the feature using a Feature Activation
Disk (FAD). FADs indicated with an asterisk are no longer required (LINCS 7.1 and higher).
Information on the older FADs has been included in case you are running an older version of
the LINCS software. LINCS supports the features previously requiring the indicated FADs,
as part of the base software.
*
g
n
i
w
o
d
n
i
W
r
e
v
r
e
S
A
N
S
X
P
I
*
P
A
D
/
C
L
D
S
*
t
r
o
p
p
u
S
U
L
A
N
S
-
n
o
N
d
e
d
n
e
t
x
E
*
S
Y
S
N
A
L
g
n
i
m
o
c
n
I
*
s
e
n
i
l
s
u
o
n
o
r
h
c
n
y
s
e
l
p
i
t
l
u
M
*
s
n
o
i
t
c
e
n
n
o
C
T
A
L
g
n
i
o
g
t
u
O
*
t
r
o
p
p
u
S
C
n
o
i
t
a
r
e
n
e
G
*
t
r
o
p
p
u
S
e
c
i
v
e
D
d
e
h
c
a
t
t
A
d
e
d
n
e
t
x
E
*
s
n
o
i
t
c
e
n
n
o
C
T
E
N
L
E
T
g
n
i
o
g
t
u
O
*
T
A
L
g
n
i
m
o
c
n
I
*
T
E
N
L
E
T
g
n
i
m
o
c
n
I
*
n
o
i
t
a
l
u
s
p
a
c
n
E
A
N
S
P
I
/
P
C
T
*
r
o
t
a
r
t
n
e
c
n
o
C
A
N
S
*
r
e
v
r
e
S
s
s
e
c
c
A
*
e
d
o
N
k
r
o
w
t
e
N
N
P
P
A
r
e
v
r
e
S
0
7
2
3
N
T
*
y
a
l
e
R
e
m
a
r
F
*
y
a
w
e
t
a
G
5
2
X
s
U
C
N
O
C
S
E
d
e
d
n
e
t
x
E
t
e
n
l
e
T
g
n
i
o
g
t
u
O
/
g
n
i
m
o
c
n
I
s
t
n
e
i
l
C
A
N
S
X
P
I
/
0
7
2
3
N
T
Windowing *
This FAD is required if any Device Profile has the windowing feature enabled.
Multiple synchronous lines *
This FAD is required if a connector other than the first connector is configured on an SCC
and/or HSC board. Only the 1st connector (e.g., HSC1.0 or SCC1.0) is allowed without the
FAD. One FAD will enable the extra connectors on all configured SCC and HSC boards.
SDLC/DAP *
This FAD is required if any Gateway Circuit has a Downstream Connection configured for
SDLC/DAP.
Extended Non-SNA LU Support *
This FAD is required if more than 32 LUs are configured on any Channel/Non-SNA Host
Circuit. It enables an additional 32 LUs to be defined on any Non-SNA Host Circuit. Up to
three Extended Non-SNA FADs may be used to allow up to 128 Non-SNA LUs for each Non-
SNA Host Circuit. If multiple channel interfaces are installed in a single LINCS node, this
FAD will enable the feature on both channel interfaces.