Ltage – Rainbow Electronics ATmega64M1 User Manual
Page 310
310
8209A–AVR–08/09
ATmega16M1/32M1/64M1
Notes:
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (10 mA at V
CC
= 5V, 6 mA at V
CC
= 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 70 mA.
2] The sum of all IOL, for ports B6 - B7, C0 - C1, D0 -D3, E0 should not exceed 70 mA.
3] The sum of all IOL, for ports B2 - B5, C4 - C7, D5 - D7 should not exceed 70 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (10 mA at Vcc = 5V, 8 mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 100 mA.
2] The sum of all IOH, for ports B6 - B7, C0 - C1, D0 -D3, E0 should not exceed 100 mA.
3] The sum of all IOH, for ports B2 - B5, C4 - C7, D5 - D7 should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
I
IL
Input Leakage
Current I/O Pin
V
CC
= 5.5V, pin low
(absolute value)
50
nA
I
IH
Input Leakage
Current I/O Pin
V
CC
= 5.5V, pin high
(absolute value)
50
nA
R
RST
Reset Pull-up Resistor
30
200
k
Ω
R
pu
I/O Pin Pull-up Resistor
20
50
k
Ω
I
CC
Power Supply Current
Active 8 MHz, V
CC
= 3V,
RC osc, PRR = 0xFF
3.8
mA
Active 16 MHz, V
CC
= 5V,
Ext Clock, PRR = 0xFF
14
mA
Idle 8 MHz, V
CC
= 3V, RC
Osc
1.5
mA
Idle 16 MHz, V
CC
= 5V,
Ext Clock
5.5
mA
Power-down mode
WDT enabled, V
CC
= 3V
t0 < 90°C
5
µA
WDT enabled, V
CC
= 3V
t0 < 105°C
9
µA
WDT disabled, V
CC
= 3V
t0 < 90°C
2
µA
WDT disabled, V
CC
= 3V
t0 < 105°C
5
µA
V
hysr
Analog Comparator
Hysteresis Voltage
V
CC
= 5V, V
in
= 3V
Rising Edge
Falling Edge
46
62
mV
mV
I
ACLK
Analog Comparator
Input Leakage Current
V
CC
= 5V
V
in
= V
CC
/2
nA
t
ACID
Analog Comparator
Propagation Delay
V
CC
= 2.7V
V
CC
= 5.0V
(6)
(6)
ns
T
A
= -40
°
C to +85
°
C, V
CC
= 2.7V to 5.5V (unless otherwise noted) (Continued)
Symbol
Parameter
Condition
Min.
Typ.
Max. Units