Comtech EF Data DMD20 - Manual (Page 58)

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–48
<1> SCC Control Ratio 1 = 1/1, 2 = 1/2, 3 = 1/3, 4 = 1/4, 5 = 1/5, 6 = 1/6, 7 =
1/7
<4> SCC In band Rate 300 to 200000 bps
<1> Fast Acquisition 0 = Disabled, 1 = Enabled
<1> Adjacent Carrier
Type
0 = Normal, 1 = High Power
<2> LBST LNB DC
Voltage Alarm Lower
Threshold Volts, Implied decimal point, 10 = 1.0V (00.0 V to 55.0
V)
<2> LBST LNB DC
Voltage Alarm Upper
Threshold Volts, Implied decimal point, 10 = 1.0V (00.0 V to 55.0
V)
<2> LBST LNB DC
Current Alarm Lower
Threshold Amps, Implied decimal point, 1000 = 1.000A (0.000 A
to 8.000 A)
<2> LBST LNB DC
Current Alarm Upper
Threshold Amps, Implied decimal point, 1000 = 1.000A (0.000 A
to 8.000 A)
<1> Number of Buffer
Clock Sources 1 - 5
<1> First Buffer Clock
Source 0 = SCTE, 1 = SCT, 2 = EXT BNC, 3 = RX SAT, 4 =
EXT IDI, Each buffer clock source must be unique
<1> Second Buffer Clock
Source 0 = SCTE, 1 = SCT, 2 = EXT BNC, 3 = RX SAT, 4 =
EXT IDI, Each buffer clock source must be unique
<1> Third Buffer Clock
Source
0 = SCTE, 1 = SCT, 2 = EXT BNC, 3 = RX SAT, 4 =
EXT IDI, Each buffer clock source must be unique
<1> Forth Buffer Clock
Source
0 = SCTE, 1 = SCT, 2 = EXT BNC, 3 = RX SAT, 4 =
EXT IDI, Each buffer clock source must be unique
<1> Fifth Buffer Clock
Source 0 = SCTE, 1 = SCT, 2 = EXT BNC, 3 = RX SAT, 4 =
EXT IDI, Each buffer clock source must be unique
<1> Asynchronous In-
Band Rate
0 =150, 1 = 300, 2 = 600, 3 = 1200, 4 = 2400, 5= 4800,
6 = 9600, 7 = 19200, 8 = 38400, 9 = 57600, 10 =
115200
<2> Rotation Ambiguity 0 = 0.0.0, 1 = 0.0.1, 2 = 0.1.0, 3 = 0.1.1, 4 = 1.0.0, 5 =
1.0.1, 6 = 1.1.0, 7 = 1.1.1
<2> RFM AGC Time
Constant 1 - 99999 in ms
<1> Carrier-in-Carrier 0 = Disabled, 1 = Enabled
<2> Carrier-in-Carrier
Minimum Search
Delay
0 – 330
<2> Carrier-in-Carrier
Maximum Search
Delay
0 – 330
<1> Carrier-in-Carrier
Frequency Offset
Range
0 – 30 (KHz)
<1> EBEM overhead
channel rate
0 = Off, 1 = 8K, 2 = 16K, 3 = 24K, 4 = 32K, 5 = 40K, 6
= 48K, 7 = 56K, 8 = 64K
<1> EBEM embedded
channel
0 = Off, 1 = On
<1> EBEM ITA 0 = Disabled, 1 = Enabled
<1> EBEM encryption 0 = Disabled, 1 = Enabled
<4> EBEM Ethernet rate 4800 to 52000000