Comtech EF Data DMD20 - Manual (Page 43)

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–33
<1> Satellite Framing 0 = No Framing, 1 = 96K IDR, 2 = 1/15 IBS, 3 = EF
AUPC 1/15, 4 = DVB, 5 = EDMAC, 6 = SCC, 7 = 96K,
8 = Efficient D&I, 9 = Ebem
<1> Drop Mode 0 = Disabled, 1 = T1-D4, 2 = T1-ESF, 3 = PCM-30, 4 =
PCM-30C, 5 = PCM-31, 6 = PCM-31C, 7 = SLC-96, 8 =
T1 D4 S, 9 = T1 ESF S
<30> Drop Map Timeslots to drop organized by satellite channel
(Mapping of Satellite Channels 1 thru 30 to dropped
Terrestrial Timeslots (Terrestrial Timeslots = 1..31))
<1> T1D4 Yellow Alarm
Select
Reserved
<1> Forced Backward
Alarms
Bit 0 = Backward Alarm 1 IDR and IBS
Bit 1 = Backward Alarm 2 IDR
Bit 2 = Backward Alarm 3 IDR
Bit 3 = Backward Alarm 4 IDR
Bits 4 & 5 = Reserved
Bit 6 = IBS Prompt
Bit 7 = IBS Service
0 = None, 1 = Force
<1> Alarm 1 Mask Bit 0 = Transmit FPGA/Processor Fault
Bit 1 = Drop DSP
Bit 2 = Transmit Symbol Clock PLL Lock
Bit 3 = Reserved
Bit 4 = IF/L-Band Synthesizer Lock
Bits 5 – 7 = Reserved
0 = Mask, 1 = Allow
<1> Alarm 2 Mask Bit 0 = Terrestrial Clock Activity Detect
Bit 1 = Internal Clock Activity Detect
Bit 2 = Tx Sat Clock Activity Detect
Bit 3 = Tx Data Activity Detect
Bit 4 = Terrestrial AIS. Tx Data AIS Detect
Bit 5 = Tx Clock Fallback
Bit 6 = DVB Frame Lock Fault
Bit 7 = TPC Conflict Check
0 = Mask, 1 = Allow
<1> Common Alarm 1
Mask Bit 0 = -12V Alarm
Bit 1 = +12V Alarm
Bit 2 = +5V Alarm
Bits 3 – 5 = Reserved
Bit 6 = IF SYNTH Alarm
Bit 7 = Spare
0 = Mask, 1 = Allow
<1> Common Alarm 2
Mask Bit 0 = TERR FPGA Config
Bit 1 = CODEC FPGA Config
Bit 2 = CODEC Device Config
Bit 3 = TRANSEC Power Test
Bit 4 = +1.5 V Rx Alarm
Bit 5 = +1.5 V TX Alarm
Bit 6 = +3.3 V Alarm
Bit 7 = +20 V Alarm
0 = Mask, 1 = Allow
<11> Tx Circuit ID 11 ASCII characters, null terminated
<1> Tx ESC Ch 1 Volume -20 to +10 (+10 dBm to –20 dBm) (two’s compliment)
<1> Tx ESC Ch 2 Volume -20 to +10 (+10 dBm to –20 dBm) (two’s compliment)