Comtech EF Data DMD20 - Manual (Page 28)

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–18
<1> Tx Terrestrial
Loopback
0 = Disabled, 1 = Enabled
<1> Tx Baseband
Loopback
0 = Disabled, 1 = Enabled
<1> Drop Status Mask Bit 0 = Frame lock fault
Bit 1 = Multiframe lock Fault. Valid in E1 PCM-30 and
PCM-30C
Bit 2 = CRC lock fault. Valid in T1ESF, and E1 CRC
enabled
Bits 3 – 7 = Reserved
0 = Mask, 1 = Allow
<1> Tx RS N Code 2 – 255, Reed-Solomon code word length
<1> Tx RS K Code 1 – 254, Reed-Solomon message length
<1> Tx RS Depth 4, 8, or 12
<1> Data Invert 0 = None, 1 = Terrestrial, 2 = Baseband, 3 = Terrestrial
and Baseband
<1> BPSK Symbol Pairing 0 = Normal Pairing, 1 = Swapped Pairing
<1> IDR Overhead Type 0 = 32K Voice, 1 = 64K Data
<1> Terminal Emulation 0 = Adds Viewpoint, 1 = VT100, 2 = WYSE50
<1> Terminal Baud Rate 0 = 300, 1 = 600, 2 = 1200, 3 = 2400, 4 = 4800, 5 =
9600, 6 = 19200, 7 = 38400, 8 = 57600, 9 = 1152000,
10 = 150
<1> FM Orderwire Mode Reserved
<1> FM Orderwire Test
Tone Reserved
<1> AUPC Local Enable 0 = Off, 1 = EF AUPC, 2 = Radyne AUPC
<1> AUPC Remote
Enable
0 = Off, 1 = EF AUPC
<1> AUPC Local CL
Action
0 = Hold, 1 = Nominal, 2 = Maximum
<1> AUPC Remote CL
Action 0 = Hold, 1 = Nominal, 2 = Maximum
<1> AUPC Tracking Rate 0 = 0.5 dB/Min, 1 = 1.0 dB/Min, 2 = 1.5 dB/Min, 3 = 2.0
dB/Min, 4 = 2.5 dB/Min, 5 = 3.0 dB/Min, 6 = 3.5 dB/Min,
7 = 4.0 dB/Min, 8 = 4.5 dB/Min, 9 = 5.0 dB/Min, 10 =
5.5 dB/Min, 11 = 6.0 dB/min
<1> AUPC Remote BB
Loopback 0 = Disabled, 1 = Enabled
<1> AUPC Remote 2047 0 = Disabled, 1 = Enabled
<2> AUPC Target Eb/No Target Eb/No at Receiver, 400 to 2000 (4.00 db to
20.00 db)
<2> AUPC Minimum
Power
For DMD20 Signed value 0 to –2500 with implied
decimal point; (0.00 to –25.00 dBm) (two’s compliment)
For OM20 Signed value -2000 to -4500 with implied
decimal point; (-20.00 to -45.00 dBm)
<2> AUPC Maximum
Power
For DMD20 Signed value 0 to –2500 with implied
decimal point; (0.00 to –25.00 dBm) (two’s compliment)
For OM20 Signed value -2000 to -4500 with implied
decimal point; (-20.00 to -45.00 dBm)
<2> AUPC Nominal
Power
For DMD20 Signed value 0 to –2500 with implied
decimal point; (0.00 to –25.00 dBm) (two’s compliment)
For OM20 Signed value -2000 to -4500 with implied
decimal point; (-20.00 to -45.00 dBm)
<1> TMT Pattern Enable Reserved
<1> TMT Pattern Length Reserved