Comtech EF Data DMD20 - Manual (Page 30)

DMD20/DMD50/DMD2050/DMD2050E/DMD1050/OM20 Remote Protocol Remote Operations
MN-DMDREMOTEOP Revision 9 1–20
<1> EBEM overhead
channel rate
0 = Off, 1 = 8K, 2 = 16K, 3 = 24K, 4 = 32K, 5 = 40K, 6
= 48K, 7 = 56K, 8 = 64K
<1> EBEM embedded
channel
0 = Off, 1 = On
<1> EBEM ITA 0 = Disabled, 1 = Enabled
<1> EBEM encryption 0 = Disabled, 1 = Enabled
<4> EBEM Ethernet rate 4800 to 52000000
<1> Ethernet HDLC 0= Radyne, 1 = Comtech, 2 = Managed 570
Status Bytes (42 Bytes)
<1> Control Mode 0 = Front Panel, 1 = Terminal, 2 = Computer, Note:
DMD20 will always return 2 = Computer
<1> Revision Number Decimal point implied
<1> Alarm 1 Bit 0 = Transmit FPGA/Processor Fault, 1 = Fail
Bit 1 = Drop DSP, 1 = Fail
Bit 2 = Transmit Symbol Clock PLL Lock, 1 = Lock
Bit 3 = Reserved
Bit 4 = IF/L-Band Synthesizer Lock, 1 = Lock
Bits 5 & 6 = Reserved
Bit 7 = Mod Summary Fault, 1 = Fail
<1> Alarm 2 Bit 0 = Terrestrial Clock Activity Detect, 1 = Activity
Bit 1 = Internal Clock Activity Detect, 1 = Activity
Bit 2 = Tx Sat Clock Activity Detect, 1 = Activity
Bit 3 = Tx Data Activity Detect, 1 = Activity
Bit 4 = Terrestrial AIS. Tx Data AIS Detect, 1 = AIS Fail
Bit 5 = Tx Clock Fallback, 1 = Clock Fallback
Bit 6 = DVB Frame Lock Fault, 1 = Fail
Bit 7 = TPC Conflict Check, 1 = Fail
<1> Common Alarm 1 Bit 0 = -12V Alarm, 1 = Fail
Bit 1 = +12V Alarm, 1 = Fail
Bit 2 = +5V Alarm, 1 = Fail
Bits 3 – 5 = Reserved
Bit 6 = IF SYNTH Alarm, 1 = Fail
Bit 7 = Spare
<1> Common Alarm 2 Bit 0 = TERR FPGA Config, 1 = Fail
Bit 1 = CODEC FPGA Config, 1 = Fail
Bit 2 = CODEC Device Config, 1 = Fail
Bit 3 = TRANSEC Power Test, 1 = Fail
Bit 4 = +1.5 V Rx Alarm, 1 = Fail
Bit 5 = +1.5 V TX Alarm, 1 = Fail
Bit 6 = +3.3 V Alarm, 1 = Fail
Bit 7 = +20 V Alarm, 1 = Fail
<1> Latched Alarm 1 Bit 0 = Transmit FPGA/Processor Fault
Bit 1 = Drop DSP
Bit 2 = Transmit Symbol Clock PLL Lock
Bit 3 = Reserved
Bit 4 = Transmit L-Band Synthesizer Lock
Bits 5 – 7 = Reserved
0 = Not Latched, 1 = Latched
<1> Latched Common
Alarm 1
Bit 0 = -12V Alarm
Bit 1 = +12V Alarm
Bit 2 = +5V Alarm
Bits 3 - 5 = Reserved
Bit 6 = IF SYNTH Alarm
Bit 7 = Spare
0 = Not Latched, 1 = Latched