KEYENCE LS-7000 - Manual (Page 112)

4-60
Chapter 4 Function Settings
4
Units, Default Minimum Values, and Setting Ranges
0.00001mm
0.01 μm
0.00000mm
0.00 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
+40.00000mm
+40000.00 μm
–99.99999~
+99.99999mm
–99999.99~
+99999.99 μm
–99.99998~
+99.99998mm
–99999.98~
+99999.98 μm
–99.99995~
+99.99995mm
–99999.95~
+99999.95 μm
–999.9999~
+999.9999mm
–999999.9~
+999999.9 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
+10.00000mm
+10000.00 μm
+10.00000mm
+10000.00 μm
+1.00000mm
+1000.00 μm
+1.00000mm
+1000.00 μm
OFF
OFF OFF
OFF
OFF
OFF OFF
OFF
0.00000mm
0.00 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
+40.00000mm
+40000.00 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
–10.00000mm
–10000.00 μm
+10.00000mm
+10000.00 μm
+1.00000mm
+1000.00 μm
–1.00000mm
–1000.00 μm
OFF
OFF
OFF
OFF
0.0000mm
0.0 μm
+30.0000mm
+30000.0 μm
0.0000mm
0.0 μm
+40.0000mm
+40000.0 μm
+30.0000mm
+30000.0 μm
0.0000mm
0.0 μm
–10.0000mm
–10000.0 μm
+10.0000mm
+10000.0 μm
+1.0000mm
+1000.0 μm
–1.0000mm
–1000.0 μm
OFF
OFF
OFF
OFF
0.00000mm
0.00 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
+40.00000mm
+40000.00 μm
+30.00000mm
+30000.00 μm
0.00000mm
0.00 μm
+10.00000mm
+10000.00 μm
+10.00000mm
+10000.00 μm
+1.00000mm
+1000.00 μm
+1.00000mm
+1000.00 μm
H-LMT
L-LMT
H-LMT
L-LMT
A–
+10V
A–
–10V
HH
HI
LO
LL
STAN-
DARD
UPPER
LOWER
Offset
Threshold
Threshold mode
Ref
erence v
alue mode
Default value
Minimum display unit
Setting item
Calibration setting
Output setting
Tolerance
setting
T1-A/B • T2-A/B
Setting range Default value Setting range Default value Setting range Default value Setting range
0.00002mm
0.02 μm
0.00005mm
0.05 μm
0.0001mm
0.1 μm
0.0002mm
0.2 μm
0.000mm
0 μm
+30.000mm
+30000 μm
0.000mm
0 μm
+40.000mm
+40000 μm
–999.9998~
+999.9998mm
–999999.8~
+999999.8 μm
–9999.999~
+9999.999mm
–9999999~
+9999999 μm
–9999.99~
+9999.99mm
–9999.9~
+9999.9mm
+30.000mm
+30000 μm
0.000mm
0 μm
–10.000mm
–10000 μm
+10.000mm
+10000 μm
+1.000mm
+1000 μm
–1.000mm
–1000 μm
OFF
OFF OFF
OFF
OFF
OFF OFF
OFF
0.00mm
+30.00mm
0.00mm
+40.00mm
+30.00mm
0.00mm
–10.00mm
+10.00mm
+1.00mm
–1.00mm
OFF
OFF
OFF
OFF
0.0mm
+30.0mm
0.0mm
+40.0mm
+30.0mm
0.0mm
–10.0mm
+10.0mm
+1.0mm
–1.0mm
OFF
OFF
OFF
OFF
0.0000mm
0.0 μm
+30.0000mm
+30000.0 μm
0.0000mm
0.0 μm
+40.0000mm
+40000.0 μm
+30.0000mm
+30000.0 μm
0.0000mm
0.0 μm
–10.0000mm
–10000.0 μm
+10.0000mm
+10000.0 μm
+1.0000mm
+1000.0 μm
–1.0000mm
–1000.0 μm
H-LMT
L-LMT
H-LMT
L-LMT
A–
+10V
A–
–10V
HH
HI
LO
LL
STAN-
DARD
UPPER
LOWER
Offset
Threshold
Threshold mode
Ref
erence v
alue mode
Default value
Minimum display unit
Setting item
Calibration setting
Output setting
Tolerance
setting
Setting range Default value Setting range Default value Setting range Default value Setting range
0.001mm
1 μm
0.01mm 0.1mm
• Each cell shows minimum display units in the order of millimeters and micrometers.
• The display unit is set to mm and the minimum display unit is set to 0.00005 (mm) before shipping.
• Set values in the table will be initialized if the change of the minimum display unit is made. Setting items
other than those in the table will not be initialized.
• If the display unit of mm is changed to μm, the minimum display unit will change from 0.00005 mm to 0.05
μm, and vice versa. Set values in the table will be initialized.
• If the program is initialized, the display unit will be set to mm and the minimum display unit will be set to
0.00005 mm. The set values will be initialized as well.