Rockwell Automation 2364F Regenerative DC Bus Supply Unit (RGU) - Manual (Page 189)

Publication 2364F-5.01– October 2003
Programming Parameters D-45
226
SCANport Clear Fault Mask
[Clear Fault Mask]
This parameter allows a connected SCANport
device to clear faults in the RGU. The selected
ports must be active (P224).
Parameter Type Sink (Read/Write)
Display Units None
Drive Units Display Units * 1
Factory Default 0111 1111
Minimum Value 0000 0000
Maximum Value 0111 1111
Related Parameters P8, P224, P225, P227
Bit Description Bit Description
0 RGU I/OClears RGU I/O faults 4 SCANport P:4Clears SCANport 4 faults
1 SCANport P:1Clears SCANport 1 faults 5 SCANport P:5Clears SCANport 5 faults
2 SCANport P:2Clears SCANport 2 faults 6 SCANport P:6Clears SCANport 6 faults
3 SCANport P:3Clears SCANport 3 faults 7 Not Used
227
SCANport Reset Mask
[Reset Mask]
This parameter allows a connected SCANport
device to reset the RGU. The selected ports must
be active (P224).
Parameter Type Sink (Read/Write)
Display Units None
Drive Units Display Units * 1
Factory Default 0111 1111
Minimum Value 0000 0000
Maximum Value 0111 1111
Related Parameters P8, P224, P225, P226
Bit Description Bit Description
0 RGU I/OResets RGU I/O 4 SCANport P:4Resets SCANport 4
1 SCANport P:1Resets SCANport 1 5 SCANport P:5Resets SCANport 5
2 SCANport P:2Resets SCANport 2 6 SCANport P:6Resets SCANport 6
3 SCANport P:3Resets SCANport 3 7 Not Used
228,229
P228 and P229 are for internal use only.
230
SCANport Disable Owner
[Disable Owner] Parameter Type Source (Read Only)
Display Units None
Drive Units Display Units * 1
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 0000 0000 0111 1111
Related Parameters P231, P232
Bit Description Bit Description
0 RGU I/OIndicates that the RGU I/O port is disabled 4 SCANport P:4Indicates that the port for SCANport 4 is disabled
1 SCANport P:1Indicates that the port for SCANport 1 is disabled 5 SCANport P:5Indicates that the port for SCANport 5 is disabled
2 SCANport P:2Indicates that the port for SCANport 2 is disabled 6 SCANport P:6Indicates that the port for SCANport 6 is disabled
3 SCANport P:3Indicates that the port for SCANport 3 is disabled 7-15 Not Used
231
SCANport Enable Owner
[Enable Owner] Parameter Type Source (Read Only)
Display Units None
Drive Units Display Units * 1
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 0000 0000 0111 1111
Related Parameters P230, P232
Bit Description Bit Description
0 RGU I/OIndicates that the RGU I/O port is enabled 4 SCANport P:4Indicates that the port for SCANport 4 is enabled
1 SCANport P:1Indicates that the port for SCANport 1 is enabled 5 SCANport P:5Indicates that the port for SCANport 5 is enabled
2 SCANport P:2Indicates that the port for SCANport 2 is enabled 6 SCANport P:6Indicates that the port for SCANport 6 is enabled
3 SCANport P:3Indicates that the port for SCANport 3 is enabled 7-15 Not Used