Warning, Operation – SkyTrak 3606 Operation Manual User Manual
Page 58
56
3606 Rev 11/99
Operation
• DO NOT raise the boom above 60° for steps 3 through 6.
• DO NOT raise the boom above 45° for steps 7 through 9.
• Follow steps 1 through 9 of the Stabil-TRAK system test procedure
exactly as written.
IMPORTANT! If the Stabil-TRAK light goes OFF and the front left tire
lowers to the ground at any time during steps 4 through 7, the test was not
performed properly or the Stabil-TRAK system is not functioning properly.
Carefully repeat the steps starting with step 1. If the Stabil-TRAK light goes
OFF and the front left tire lowers to the ground consistently during steps 4
through 7, the Stabil-TRAK system is not functioning properly and the test
should be stopped immediately. DO NOT use the vehicle if the Stabil-TRAK
system is not functioning properly. Contact your local
Sky Trak
Distributor
immediately to repair the system.
Stabil-TRAK™ System Test Procedures
1. Fasten seat belt and place the vehicle on a level surface with 0°
sway, no load on the forks, boom fully retracted and horizontal.
Check to be sure the Stabil-TRAK light is OFF. See page 33 for the
location of the light in the display panel.
2. Locate an 8 inch (203,2 mm) wood or cement block in front of the
left front tire and drive the vehicle up on the block. Use the frame
sway control to level the vehicle back to 0°.
3. With the service brake pedal depressed, the parking brake switch
OFF, move the travel select lever to the (N) NEUTRAL position and
raise the boom to exactly 60°. The Stabil-TRAK light should come
ON when the boom angle is at about 40° and remain ON.
IMPORTANT! Perform procedures 4 through 9 with the engine rpm at idle.
4. While the service brake pedal is depressed, move the travel select
lever to the (R) REVERSE position. Ease your foot off the service
WARNING
DO NOT operate this vehicle unless you are in the seat with the seat
belt fastened around you. Death or serious injury could result if the belt
is not securely fastened.
56
3606 Rev 11/99
Operation
• DO NOT raise the boom above 60° for steps 3 through 6.
• DO NOT raise the boom above 45° for steps 7 through 9.
• Follow steps 1 through 9 of the Stabil-TRAK system test procedure
exactly as written.
IMPORTANT! If the Stabil-TRAK light goes OFF and the front left tire
lowers to the ground at any time during steps 4 through 7, the test was not
performed properly or the Stabil-TRAK system is not functioning properly.
Carefully repeat the steps starting with step 1. If the Stabil-TRAK light goes
OFF and the front left tire lowers to the ground consistently during steps 4
through 7, the Stabil-TRAK system is not functioning properly and the test
should be stopped immediately. DO NOT use the vehicle if the Stabil-TRAK
system is not functioning properly. Contact your local
Sky Trak
Distributor
immediately to repair the system.
Stabil-TRAK™ System Test Procedures
1. Fasten seat belt and place the vehicle on a level surface with 0°
sway, no load on the forks, boom fully retracted and horizontal.
Check to be sure the Stabil-TRAK light is OFF. See page 33 for the
location of the light in the display panel.
2. Locate an 8 inch (203,2 mm) wood or cement block in front of the
left front tire and drive the vehicle up on the block. Use the frame
sway control to level the vehicle back to 0°.
3. With the service brake pedal depressed, the parking brake switch
OFF, move the travel select lever to the (N) NEUTRAL position and
raise the boom to exactly 60°. The Stabil-TRAK light should come
ON when the boom angle is at about 40° and remain ON.
IMPORTANT! Perform procedures 4 through 9 with the engine rpm at idle.
4. While the service brake pedal is depressed, move the travel select
lever to the (R) REVERSE position. Ease your foot off the service
WARNING
DO NOT operate this vehicle unless you are in the seat with the seat
belt fastened around you. Death or serious injury could result if the belt
is not securely fastened.