Watlow Series F4S/D - Manual (Page 59)

Wa t l o w S e r i e s F 4 S / D S e t u p ■ 5 . 1 1
Setup Page Parameter Table
Modbus
Register
Range read/write Conditions for
Parameter Description (Modbus Value) Default (I/O, Set, Ch) Parameters to Appear
✔ NOTE:
For more information about how parameter settings affect the con-
troller’s operation, see the Features Chapter.
Active: Always. Output
715 [1A]
732 [1B]
749 [2A]
766 [2B]
r/w
0% (0) 0% to High Limit -1
(0 to High Limit -1)
Low Power Limit
Set low limit control
(PID mode only)
output power level.
Active: Always. Output
714 [1A]
731 [1B]
748 [2A]
765 [2B]
r/w
100% (100) Low Limit +1 to 100%
(Low Limit +1 to 100)
High Power Limit
Set high limit con-
trol (PID mode only)
output power level.
Active if the selected output is
set to a process output.
Output
701 [1A]
718 [1B]
735 [2A]
752 [2B]
r/w
4 to 20mA (0) 4 to 20mA (0)
0 to 20mA (1)
0 to 5V (2)
1 to 5V (3)
0 to 10V (4)
Process
Set process output
type.
Active if the selected output is
not Process and Burst is set to
No.
Output
506 [1A]
556 [1B]
2506 [2A]
2556 [2B]
r/w
Fixed Time
1.0 sec. (10)
.1 to 60
(1 to 600)
Enter Cycle Time
Select the duration
of cycle.
Active always. Output
509 [1A]
559 [1B]
2509 [2A]
2559 [2B]
r/w
Variable Burst (0)
Fixed Time (1)
Choose Cycle Time
Enter the value of
the variable burst
cycle time.
Active if Analog Inputs 1 and 2
are enabled.
Output
700 [1A]
717 [1B]
734 [2A]
751 [2B]
r/w
Heat (1A and
2A) (1)
Off (1B, 2B)
(0)
Off (0)
Heat (1)
Cool (2)
Function
Select type of func-
tion for output.
Main > Setup > Control Output x (1A,1B, 2A and 2B)
Control Output x (1A,1B, 2A and 2B)
Active: Always.
Digital inputs are edge trig-
gered and require a transition
from high to low or low to high.
Input
1061 [1]
1063 [2]
1065 [3]
1067 [4]
r/w
Low (0) Low (0)
High (1)
Condition
Select the condition
to trigger digital
input.
Active: Always.
While a profile is running, the
controller will not recognize
digital inputs that are pro-
grammed to start a profile.
Only one profile can be run at a
time.
* This prompt only appears if the
F4 memory contains a profile.
Input
1060 [1]
1062 [2]
1064 [3]
1066 [4]
r/w
Off (0) Off (0)
Panel Lock (1)
Reset Alarm (2)
Control Outputs Off (3)
All Outputs Off (4)
Digital Outputs Off (5)
Start Profile (6)*
Pause Profile (7)
Resume Profile (8)
Terminate Profile (9)
Wait for Event (10)
Function
Select the digital
input function.