Watlow Series F4S/D - Manual (Page 144)

A . 1 0
■
A p p e n d i x Wa t l o w S e r i e s F 4 S / D
action 5.7
indicator lights 2.2
Information Key 1.4, 2.4, 2.7
Input 1 Only, Process Display 5.15
Input 1 wiring 12.3
Input 2 wiring 12.4–12.5
Input 3 wiring 12.4–12.5
input calibration 9.2–9.4
input errors 3.9
input status 2.8
input wiring 12.3–12.5
Input x Error 2.8
Input x Failure 5.7
input-to-output isolation 12.1
inputs and outputs 1.1
calibration 9.2–9.6
dual-channel Series F4 1.1
single-channel Series F4 1.1
wiring, overview 12.1–12.2
insert step 4.6
installation
dimensions 11.1
installing 11.2
overview 11.2–11.3
tools required 11.2
Integral Reset Adjustment 3.5
Integral x
Cascade Inner Loop 3.11
Cascade Outer Loop 3.13
PID Set 1 to 5 3.11
PID Set 6 to 10 3.12
Internal Cascade SP 6.11
isolation barriers 12.1
J
Jump
Count 4.15
Profile 4.15
Repeats 4.15
Step 4.13, 4.15
K
keys
Information Key 1.4, 2.4, 2.7
Left and Right Keys 2.4, A.17
Profile Key 2.4, A.17
Up and Down Keys 2.4, A.17
keys, displays and navigation,
overview 2.1, A.17
L
Latching, Alarm Output x 5.12
Line Frequency 10.3
linearization table 5.8
lockout 8.1–8.3
locks 8.3
Clear Locks 8.3
levels 8.1
Set Lock 8.3
Low Power Limit 5.11
Low Scale 5.12, 6.3
Lower Display 2.2
M
Main Page 2.3, 2.8
Alarm x Condition 2.8
Autotuning Channel x 2.8
Custom Main Page 2.3, 5.2, 5.3
default Main Page 2.3
error messages on 2.3
parameter table 2.8
manual operation, not allowed, 3.1
manual tuning 3.5–3.6
Manufacture Date 10.2
map, software A.16–A.17
menu and page maps
all A.16–A.17
Calibration Menu 9.6
Communications Menu 5.14, 7.16
Diagnostics Menu 10.1
Operations Page 3.10
Profiles Page 4.11
Set Lockout Menu 8.2
Setup Page 5.6
Message 1 to 4, Static Message 5.15
Military Standard Test 810D 3.7,
4.8–4.9
Modbus registers
alphabetical listing 7.2–7.10
numerical listing 7.13–7.15
profile parameters 7.10–7.12
Modbus Remote Terminal Unit (RTU)
7.1
Modbus RTU protocol 7.1
Model Number 12.1, A.7
Model, Diagnostic 10.2
multiple PID sets 3.5, 6.6
multiple tuning procedure 3.5
N
Name
Alarm Output x 5.12
Digital Input x 5.10
Digital Output x 5.13
names, how to enter 2.6
naming
alarm output 2.6, 5.13
digital input 2.6, 5.10
digital output 2.6, 5.12
profiles 2.6, 4.4
navigation 2.4
navigation keys 2.4
noise filter 6.2
non-volatile memory 4.2
numbers, how to enter 2.6
O
On-Off control 6.4
chattering 6.4
Hysteresis x (A or B) 6.4
Proportional Band x (A or B) 6.4
Open Loop Channel x, enable 5.7
Open Loop Detect 6.2
operations
overview 3.1
profile control 3.2
sample application 3.7
Operations Page
map 3.10
Parameter Record 3.15
parameter table 3.11
operator’s display, see lower display
ordering information A.7
Output Calibration 9.4–9.6
output condition, indicators 2.2
Outputs, Event, number of 1.1
outputs x (1A, 1B, 2A and 2B)
type 10.2
wiring 12.7–12.8
P
P (Parameter) x, Custom Main Page
5.15
page and menu maps
all A.16–A.17
Calibration Menu 9.6
Communications Menu 5.14, 7.16
Diagnostics Menu 10.1
Operations Page 3.10
Profiles Page 4.11
Set Lockout Menu 8.2
Setup Page 5.6
pages, software 2.1, A.16–A.17
Panel Lock 5.5
parameter record
Custom Main Page 5.3