Watlow Series F4S/D User Manual
Page 145
Wa t l o w S e r i e s F 4 S / D
A p p e n d i x
■
A . 1 1
Operations Page 3.15
Profile 4.7
Setup Page 5.16
parameter setup order 5.1–5.2
parameter tables
Calibration Menu 9.7–9.8
Communications Menu 5.14, 7.16
Diagnostic Menu 10.2–10.3
Main Page 2.8
Operations Page 3.11–3.14
Profiles Page 4.12–4.16
Set Lockout Menu 8.3
Setup Page 5.7–5.15
Test Menu 10.4
password lock 8.1
password, setting or changing 8.2
pattern — see profile
pause (Hold) profile 4.3
Percent Power Output, status 7.2
PI control 6.5
droop 6.5
Integral 6.5
overshoot 6.5
reset 6.5
PID block, see PID set
PID control 6.5
PID parameters, adjusting manually
PID sets 6.6
PID Units 5.1, 5.7
PID values, defaults 3.4
Power Out Condition 4.3
power wiring 12.2
Power-Out Action 5.7
Power-Out Time 5.7
Process Display 5.15
process input range limits
process input, wiring 12.2
process or deviation alarms 3.4, 6.8
Process Output, Calibration 7.7, 9.4
Output 1 Calibration 7.7, 9.4
Output 2 Calibration 7.7, 9.4
Process, Control Output x 5.11
Profile Action Menu 3.3
profile control 3.2, 5.10
profile indicator light 2.2
Profile Key 2.4, 3.2, 3.3
hold a profile 3.3
resume a profile 3.3
run a profile 3.2
start a profile 3.2
profile lockout 7.8, 8.1
profile mode 3.2
profile number 7.12
profile plan checklist 4.3
profile programming
editing a profile 4.6
frequently asked questions 4.10
Modbus flowcharts 7.17–7.26
new profile 4.4
overview 4.1
procedures 7.17–7.26
Profiles Page parameters
sample profile 4.8–4.9
step types 4.2–4.3, 4.12, 4.16
User Profile Record 4.7
profile Modbus registers 7.10–7.12
Profile Status message 3.2
profile wait for, analog input x or
profile, defined 4.2
Profiles Page 4.4
create profile 4.4
edit profile 4.6
map 4.11
programming new profile 4.4–4.5
Proportional Band x 6.4
adjustment 3.5
Cascade Inner Loop 3.11
Cascade Outer Loop 3.13
PID Set 1 to 5 3.11
PID Set 6 to 10 3.12
proportional plus integral (PI) control
droop 6.5
integral 6.5
overshoot 6.5
reset 6.5
proportional plus integral plus
PV bias, see calibration offset
Q
R
Ramp Rate 4.2, 4.12–4.13
Ramp Set Point Channel x 4.13
ramp steps, number of 1.1
Ramp Time 4.12–4.13
ramping mode 3.2
ramping profile 4.2
range high 6.3
range low 6.3
Rate 6.5
Cascade Inner Loop 3.12
Cascade Outer Loop 3.13
PID Set 1 to 5 3.1 1
PID Set 6 to 10 3.12
read only 8.1
real-time clock 1.1
recipe —see file or profile
Records
Custom Main Page 5.3
Operations Page Record 3.15
Profile Page Record 4.7
Setup Page Record 5.15
reference compensator 9.2
registers
Modbus 7.2–7.15
profile 7.10–7.12
relative humidity (RH) 5.5
removing the controller 11.3
renaming profiles, see naming,
profiles
Cascade Inner Loop 3.11
Cascade Outer Loop 3.13
PID Set 1 to 5 3.11
PID Set 6 to 10 3.12
resistance temperature detector
restore factory calibration values 9.1
Resume Profile 3.3
retransmit outputs
calibration 9.5–9.6
diagnostics 10.3
wiring 12.8
Retransmit Source 5.12
retransmitting 6.3
chart recorder 6.3
outputs 1 and 2 6.3
remote set point 6.3
input, calibration 9.2
inputs, wiring 12.3–12.4
S
safety info ii
sample application, enviroonmental