Symbol definitions, Command/response table, For ip-specific sis commands – Extron Electronics MTPX Plus 6400 Series User Guide User Manual
Page 89

Command/Response Table for IP-Specific SIS Commands
Symbol definitions
X4)
= Matrix name
(Up to 240 alphanumeric characters)
NOTE: The following characters are invalid or not recommended in the name: {space} + ~ , @ = ` [ ] { } < > ‘ “ ” ; : | \ and ?.
X4!
= Default name
MTPX- + last 3 pairs of MAC address
X4@
= Time and date (for set)
In the format: MM/DD/YY•HH:MM:SS where:
MM = month: 01 (Jan) through 12 (Dec)
DD = day: 01 through 31
YY = year: 00 through 99
HH = hour: 00 through 23
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X4#
= Time and date (for read)
In the format: Day,•DD•Mmm•YYYY•HH:MM:SS where:
Day = weekday: Mon through Sun
DD = date: 01 through 31
Mmm = month: Jan through Dec
YYYY = year: 2000 through 2099
HH = hour: 00 through 24
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X4$
= GMT offset
–12.0 through +14.0. Hours and minutes removed from GMT
X4%
= Daylight Saving Time
0 = Daylight Saving Time off/ignore
2 = Daylight Saving Time on (Europe)
1 = Daylight Saving Time on (North America)
3 = Daylight Saving Time on (Brazil)
X4^
= IP address
nnn.nnn.nnn.nnn
X4&
= Hardware (MAC) address
nn-nn-nn-nn-nn-nn
X4*
= Number of open connections
0 – 255
X4(
= Password
12 alphanumeric characters
NOTE: The following characters are invalid or not recommended in passwords: {space} + ~ , @ = ` [ ] { } < > ‘ “ ” ; : | \ and ?.
X5)
= Domain name
Standard domain name rules apply (for example: xxx.com)
NOTE: The following characters are invalid or not recommended in a domain name: {space} + ~ , @ = ` [ ] { } < > ‘ “ ” ; : | \ and ?.
The @ character is acceptable only as the lead-in to the domain name (such as @extron.com).
X5!
= E-mail account
65 - 72. 65 = e-mail recipient 1, 66 = 2, 67 = 3, ... 72 = recipient 8
X5@
= E-mail address
Typical e-mail address format (for example: nnnn@xxx.com)
X5#
= Notification selections, part 1
F = fans
P = power supply
X5$
= Notification selections, part 2
If
X5#
= F, then
X5$
= 00 (all fans)
If
X5#
= P, then
X5$
= 00 (all power supplies)
X5%
= Notify when?
0 = no response
1 = fail/missing
2 = fixed/restored
3 = both 1 & 2
4 = suspend
X5^
= DHCP
0 = off, 1 = on
X5&
= Port number
01 = Remote RS233/RS422 port
02 (unused)
03 – 66 = UARTs 1 through 64
X5*
= Baud rate
9600, 19200, 38400, 115200
X5(
= Parity
odd, even, none, mark, space (Only the first letter is required.)
X6)
= Data bits
5 – 8 (8 = default)
X6!
= Stop bits
1, 2 (1 = default)
X6@
= Port type
0 = RS-232, 1 = RS-422
X6#
= Verbose mode
0 = clear or none (default for Telnet connection)
2 = tagged responses for queries
1 = verbose mode (default for RS-232 or RS-422 connection) 3 = verbose mode and tagged for queries
NOTE: If tagged responses is enabled, all read commands return the constant string and the value as the set command does
(for example, the read matrix name command
E
CN
}
, returns Ipn•
X4)]
).
X6$
= Port timeout interval
1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
(in 10-sec. increments)
MTPX Plus 6400 Series Matrix Switchers • Programming Guide
83