Extron Electronics MTPX Plus 6400 Series User Guide User Manual
Page 85
Command/Response Table for SIS Commands (continued)
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
View ties, gain, volume, mutes, and presets status
NOTE: The
& read RGB tie command and % read video tie command can be used interchangeably.
View output video (RGB) tie
X@
&
X!]
Example:
15&
27
]
Input 27 is tied to output 15.
View output video tie
X@
%
X!]
Example:
7%
Ø2
]
Input 2 is tied to output 7.
View output audio tie
X@
$
X!]
Example:
3$
Ø6
]
Input 6 audio is tied to output 3.
View output volume
X1&
V
X1*]
Example:
7V
55
]
Volume for output 7 is 55%.
View input gain
X1!
G
X2)]
Example:
4G
-Ø2
]
Gain for input 4 is -2 dB.
View output mutes
E
VM
}
X2^
1
X2^
2
...
X2^
n
]
Each
X2^
response is the mute status of an
output, starting from output 1.
n is the highest-numbered installed output.
Example:
MTPX Plus 6432
E
VM
}
Mut022020 ... 02202000
]
Output 2, 3, 5, 27, 26, and 29 audio or
RS-232 are muted. All other outputs are
unmuted.
NOTE: The
Mut portion of the response appears only when the switcher is in Verbose mode 2 or 3 (see the “
” SIS
command on page 85).
View global video preset
configuration
EX2@
*
X@
*1VC
}
X!
n
•
X!
n+1
• ... •
X!
n+15
•Vid
]
Show the configuration of preset
X2@
. Show
the input tied to 16 sequential outputs,
starting from output
X@
. n is the starting
output number.
Command description:
preset # (
X2@
)*starting output # (
X@
)*1 (= video)VC
Response description:
input # (
X!
) tied to
X@
•
X!
tied to
X@
+1•
X!
tied to
X@
+2• ... •
X!
tied to
X@
+15•Vid
]
Example
MTPX Plus 6432
:
E
23*25*1VC
}
Output:
Response = tied input:
input 2 tied to output 27
32
31
30
29
28
27
26
25
no tied input
input 8 tied to output 28
37 38 39 40
33 34 35 36
outputs do not exist
Ш8•Ш8•Ш2•Ш8•Ш8•Ш1•ШШ•ШШ
•Vid
•--•--•--•--•--•--•--•--•
Each position shown in the response is an output: left = output 25 (the starting output number), right = output 32.
(Outputs 33 through 40 are not present on this matrix switcher.) The number in each position is the input tied
to that output.
In this example, video input 8 is tied to outputs 25, 26, 28, and 29; input 2 is tied to output 27; and input 1 is
tied to output 30. No inputs are tied to outputs 31 and 32.
NOTE:
EX2@
*1*1VC
}
where
X2@
= 0 returns the current video configuration of the switcher.
NOTE:
X!
= Input number
00 – maximum number of inputs for your matrix size (00 = untied)
X@
= Output number
01 – (maximum number of outputs for your matrix size)
X1!
= Input number
01 – (maximum number of inputs for your matrix size)
X1&
= Local audio output number
01 – 08
X1*
= Volume adjustment range
00 – 64 (see the table above)
X2)
= Numeric dB value
–18 to + 24 (45 steps of gain or attenuation( (Default = 0 dB)
X2@
= Global or room preset number
01 – 64 (global) or 01 – 10 (room)
X2#
= Name
12 characters maximum
Upper- and lower-case alphanumeric characters and _ / and spaces are valid.
X2$
= Room number (for room presets)
01 – 10
X2^
= Audio or RS-232 mute
0 = no mutes
2 = audio or RS-232 mute
MTPX Plus 6400 Series Matrix Switchers • Programming Guide
79